TY - JOUR ID - TI - Nugget mechanical properties of combination (rectangular and round) welded and soldered stainless steel wires AU - Zainab M. Hasan AU - Fakhri A. Ali فخري عبد علي PY - 2014 VL - 26 IS - 3 SP - 169 EP - 173 JO - Journal of baghdad college of dentistry مجلة كلية طب الاسنان بغداد SN - 18171869 23115270 AB - Background: This study aimed to compare the mechanical properties between four groups of newly fabricatedcombination wires according to their method of union, according to the gauges of wires and a comparison weremade between them and their originals.Materials and method: A total of 60 stainless steel combination wires were fabricated , divided into four groupsaccording to gauge of wires and their method of union, each of them with 15 samples, the groups were welded(0.016x0.022-0.016 and 0.016x0.022-0.018) and soldered (0.016x0.022-0.016 and 0.016x0.022-0.018), samples weremade according to certain parameters which were : for the welded samples: length,weight, duration of pulsationand size of copper electrode tips used; for the soldered samples: length, weight, distaince from the heat source andduration of heat applicationResults: The descriptive statistics showed that the maximum value for ultimate force and ultimate tensile strength wasfor the soldered 0.016x0.022+0.018 inches combination wires, while the minimum was for the welded0.016x0.022+0.016inches wires. Elastic modulus showed higher values for the soldered 0.016x0.022+0.016 and resiliencyvalues for the welded 0.016x0.022+0.016 were the highest. Comparison between combination wires and theiroriginals showed a decrease in the mechanical properties after soldering and welding.Conclusion: Higher gauge wires and soldering method of union showed better mechanical properties than the othergroups and both soldering and welding method showed changes in the mechanical properties of the newlyfabricated wires when comparing them with their originals

المقدمة: تھدف ھذه الدراسة إلى المقارنة بین الخواص المیكانیكیة بین أربع مجموعات من الأسلاك المركبھ وفقا لطریقتھم في الاتحاد،وفقا لقیاسات الأسلاك وتم إجراء مقارنة بینھاوبین الاسلاك الاصلیھ.المواد والطریقھ: مجموعھ من 60 سلك مصنوع من مادة الفولاذ المقاوم للصدأ ، قسمت الى أربع مجموعات وفقا لقیاسات الأسلاك وطریقةاللحام، كل واحد منھم یتكون من 15 عینة،0.022 ) وفقا لبعض الضوابط والتي كانت: الطول، الوزن،ومدة النبض وحجم نحاس االاقطاب x0.016+ 0.022 و 0.018 x0.016+ تم لحم الاسلاك ذات القیاسات التالیھ ( 0.016المستخدمة (بلنسبھ للعینات الملحومھ عن طریق التیار الكھربائي) ومدة عملیة اللحام والبعد من مصدر الحراره (للعینات الملحومھ عن طریق الحراره).0.018-0.022 ) قیم عالیة بالمقارنة مع العینات الاخرى الاقل × النتائج:أظھرت النتائج للقوه القصوى المحتملھ ولقوة الشد القصوى للعینات الملحومھ عن طریق الحراره ( 0.0160.016-0.022 ) قیم عالیھ بلمقارنھ مع العینات الاخرى × حجما والملحومة عن طریق التیار الكھربائي, و اظھرت نتائج معامل المرونھ للعینات الملحومھ عن طریق الحراره( 0.016(0.016 -0.022 × الاكبر حجما الملحومھ عن طریق التیار الكھربائي , اما نتائج معامل الطاقھ المخزونھ فقد اظھرت قیم عالیھ للعینات الملحومھ عن طریق التیار الكھربائي ( 0.016وقد لوحظ انخفاضا في الخواصالمیكانیكیھ عند مقارنة الاسلاك المركبھ مع الاسلاك الاصلیة قبل اللحیم.الخلاصةأظھرت الأسلاك ذات القیاس الأعلى وأسلوب لحام عن طریق الحراره خواصامیكانیكیة أفضل من المجموعات الأخرى وعلى حد سواء عند مقارنة الاسلاك الجدیده مع النسخ الأصلیةالخاصة بھم اظھرت النتائج انخفاضا في الخواصالمیكانیكیھ بلنسبھ للاسلاك المركبھ الجدیده. ER -