TY - JOUR ID - TI - BUCKLING OF STEEL PORTAL FRAMES CONSIDERING MATERIAL NON-LINEARITY إنبعاج الأطر الفولاذية المقنطرة باعتبار لاخطية خواص المواد AU - Orabi Al Rawi AU - Hani Qadan هانئ عبدالكريم قعدان AU - Shehdeh Ghannam شحدة محمد سلام غنام PY - 2015 VL - 8 IS - 2 SP - 72 EP - 83 JO - DIYALA JOURNAL OF ENGINEERING SCIENCES مجلة ديالى للعلوم الهندسية SN - 19998716 26166909 AB - In this research, an experimental study was carried out to investigate the failure modes of eight frames with IPE cross-sections. The study was conducted by subjecting these frames to two equal concentrated loads (applied directly on columns); however, the resulted data was obtained using load cells to record load increments. Comparison between experimental and theoretical results was tabulated by analyzing the eight portal frames using the following methods:1-Quasilinear analysis.2-Non-linear material analysis. 3-Codes AISC ASD, and AISC LRFD.For non-linear material analysis, direct tensile and stub column tests were performed to obtain the secant modulus as a function of plastic energy density. A mathematical formula was designed for this purpose using a special computer program. Moreover, a comparison of "AISC LRFD & AISC ASD" with the experimental results were implemented. Furthermore, the non-linear material model was also applied to these Codes. Linear analysis gives a reasonable approximation to deflections before yield occurs. Calculation of buckling loads for different frames using Euler formula, ASD, and finite element quasilinear analysis are significantly overestimate the experimental results. Whereas, incorporating the non-linear material model into the above mentioned methods of analysis brings the values very close to the experimental results.

في هذا البحث تم اجراء تجارب على ثماني اطر فولاذية مقنطرة وذلك بتطبيق احمال مركزة فوق العناصر العامودية. تم تسجيل النتائج بواسطة مقاييس تشوه حيث تم ربطها بحاسوب.تم مقارنة النتائج العملية بالدراسة النظرية من خلال تحليل الاطر الثمانية بالطرق التالية:- التحليل شبه الخطي- التحليل الخطي- الكودات العالمية ( (AISC ASD, AISC LRFDولتحديد الخواص الميكانيكية لعينات الفولاذ فقد تم اجراء فحوصات شد وضغط حيث تم استنتاج علاقة لاخطية بين الاجهاد والتشوه لهذه العينات. وبناء على هذه العلاقة فقد تم استنتاج علاقة معامل المرونة بالطاقة الداخلية لهذه المقاطع وذلك باستخدام طرق احصائية.تم استخدام العلاقة الاخيرة في طرق التحليل النظريه اعلاه وتم عمل مقارنة بالنتائج العملية.اثبتت هذه الدراسة حساب الترخيم باستخدام الطرق الخطية بأنها قريبة من النتائج العملية. اما في حساب مقاومة قوة الانبعاج، فقد اثبتت الدراسة ان استعمال طريقة التحليل اللاخطي يؤدي الى نتائج ادق وقريبة من النتائج العملية. ER -