TY - JOUR ID - TI - Parametric Study of Continous Composite Steel-Concrete Beam with External Prestressing دراسة عوامل العتبات المستمرة المركبة من الحديد والخرسانة مع اجهاد مسبق خارجي AU - Amer M. Ibrahim AU - Wissam D. Salman PY - 2015 VL - 33 IS - 3 Part (A) Engineering SP - 738 EP - 752 JO - Engineering and Technology Journal مجلة الهندسة والتكنولوجيا SN - 16816900 24120758 AB - In the present study, three-dimensional nonlinear finite element analyses were conducted to investigate the effect of several important parameters on the behavior of the external prestressed continuous composite steel-concrete beam. These parameters included the effects of concrete compressive strength, ratio of effective prestressing to ultimate stress (fpe/fpu), external prestressing technique, ratio of thickness to width of concrete slab (T/B), transfer load point to mid span section, type of loading, full and partial interaction, tendon profile, and number of stiffeners. It had been found that, at increasing the concrete compressive strength from (20 to 60MPa) and the ratio of prestress to ultimate stress from (0.264 to 0.79), the ultimate load was increased by about (19.64%) and (9.05), respectively. The ultimate load of a continuous composite beam with external prestressing was increased by about (26.63%) than the same continuous beam without prestressing. The increase in the ultimate load of the continuous beam subjected to three point loads on each span was (25.93%) larger than that of the continuous beam with a single load on each span. It was noted that the ultimate capacity was increased by (7.32%) when draped tendon profile was used. Also it was noted that the ultimate load of beam with full interaction is (3.25%) greater than the same beam with partial interaction. Increasing the thickness to width of concrete slab ratio, from (0.1 to 0.25) with constant area of concrete, led to an increase in the ultimate load by about (6.60%). It was noted that the ultimate capacity increased by about (8.25%) when number of stiffeners were increased from three to seven.

التحليل اللاخطي الثلاثي الابعاد تم اجراءه باستخدام طريقة العناصر المحددة لبحث تأثير عدة عوامل مهمة على تصرف العتبات المستمرة المركبة من الحديد والخرسانة مع اجهاد مسبق خارجي. ھذه العوامل تضمنت تأثير مقاومة الانضغاط للخرسانة، نسبة الاجھاد المسبق الفعال الى الاجھاد الاقصى، تقنية الاجهاد الخارجي المسبق, نسبة سمك الى عرض السقف الخرساني, انتقال القوة الى وسط مقطع العتبة, نوع التحميل، الترابط الجزئي او الكلي, شكل الوتر وعدد التقويات. وجد بزيادة مقاومة الانضغاط للخرسانة من (20 to 60 MPa) ونسبة الاجهاد المسبق الفعال الى الاجهاد الاقصى من (0.264 to 0.79) فان التحمل الاقصى سيزداد بمقدار (19.64%) و (8.05) على التوالي. التحمل الاقصى للعتبات المستمرة المركبة مع الاجهاد المسبق الخارجي اكثر بحدود (26.63%) من تحمل نفس العتبات المستمرة المركبة بدون اجهاد مسبق خارجي, وان الزيادة في التحمل الاقصى للعتبات المستمرة المعرضة لثلاث نقاط تحميل لكل فضاء هي (25.93%) اكثر من تحمل العتبات المستمرة المعرضة لنقطة تحميل واحدة لكل فضاء, ومن الملاحظ ايضا ان التحمل الاقصى يزداد بحدود (7.32%) عند استخدام الاوتار المثنية الشكل بدلا من الاوتار المستقيمة. وكذلك لوحظ ان التحمل الاقصى يزداد بحدود (3.25%) عند استخدام الترابط الكلي بدلا من الترابط الجزئي وبزيادة نسبة سمك الى عرض السقف الخرساني من ( 0.1 to 0.25) فان التحمل الاقصى سيزداد بحدود (6.60%) وان التحمل الاقصى يزداد بحدود (8.25%) عند زيادة عدد التقويات من ثلاثة الى سبعة مزدوجات. ER -