@Article{, title={Experimental and Numerical Analysis of Bulletproof Armor Made from Polymer Composite Materials التحليل العددي والعملي لدرع مضاد للرصاص مصنوع من مواد متراكبة بوليمرية}, author={Jawad Kadhim Oleiwi and Abass Khammas Hussein and Sura Hameed Ahmed}, journal={Engineering and Technology Journal مجلة الهندسة والتكنولوجيا}, volume={33}, number={7 Part (A) Engineering}, pages={1583-1597}, year={2015}, abstract={This work focuses on the preparation of polymer matrix composite specimens by (Hand Lay-Up) method to make bulletproof armor from the unsaturated polyester resin (UP) as a matrix reinforced by Kevlar fibers at different volume fractions with and without (3%) of Al2O3 powder. The tensile test was performed for these composite specimens which include: (modulus of elasticity, tensile strength and elongation percentage), in addition of ballistic test were studied. The results of this work show that the values of tensile test increase with increasing the volume fraction of fibers. And the values of tensile test of a composite reinforced by kevlar fibers and addition (3%) of Al2O3 powder was less than those composite without addition of Al2O3 powder. The numerical method based on FEM was used to analysis of the bullet proof armor ballistic test of the composite specimens by finding the values of stresses, strains and deformations. The numerical results that obtained from the program (ANSYS 14.5) represent the maximum value of stress happened to the composite specimens when reinforced by eight layers of the kevlar, and vice versa to the deformations and strain also the numerical results shown a good agreement with results that were obtained experimentally. Results of ballistic test of composite specimens show the volume fraction of fibers has an effect on the deformations of the front face and back face of these composite specimens. And the values of the ballistic test for the composite reinforced by kevlar at eight layers give the best values from other each of composite specimens.

في هذا البحث تم تحضير مواد متراكبة ذات اساس بوليمري بطريقة الصب اليدوي لعمل درع مضاد للرصاص من راتنج البولي استر غير المشبع كمادة اساس مدعمة بالياف الكفلر عند كسور حجمية مختلفة مع اضافة او عدم اضافة (3%) من دقائق الـ ((Al2O3. اجريت على هذه العينات المتراكبة اختبار الشد والذي تضمنه (معامل المرونة, مقاومة شد, ونسبة الاستطالة), بالإضافة الى اختبار الاطلاق . اظهرت نتائج هذا البحث ان قيم اختبار الشد تزداد مع زيادة الكسر الحجمي للالياف. وان قيم اختبار الشد للعينات المتراكبة عند اضافة (3%) من دقائق الـ (Al2O3) هي اقل من قيم هذه المواد المتراكبة بدون اضافة دقائق الـ (Al2O3) . استخدمت الطريقة العددية المعتمدة على طریقة العناصر المحددة لتحلیل اختبار الاطلاق للدرع المضاد للرصاص للعينات المتراكبة بواسطة ايجاد الاجهادات والانفعالات والتشوهات. بينت النتائج العددية التي تم الحصول علیها من استخدام برنامج (ANSYS 14.5) ان اقصى قيم للاجهاد تحدث للعينات المتراكبة عندما تقويتها بثمانية طبقات من الياف الكفلر والعكس بالعكس لقيم الانفعال والتشوه, وكذلك بينت النتائج العددية تطابق جيد مع النتائج العملية. بينت نتائج فحص الاطلاق للعينات المتراكبة بان الكسر الحجمي للالياف تؤثر على تشوهات الوجه الامامي والوجه الخلفي لهذه العينات. وان قيم اختبار الاطلاق للمواد المتراكبة المقواة بالياف الكفلر عند ثمانية طبقات اعطت افضل قيم من كل العينات المتراكبة الاخرى.} }