TY - JOUR ID - TI - Preparation and Characterization of BeO-Supported Feldspar Porcelain خصائص ومواصفات خزف الفلدسبار المدعم باوكسيد البريليوم AU - Dunia K. M. Al-Nasrawy دنيا كامل مهدي النصراوي PY - 2016 VL - 57 IS - 1B SP - 404 EP - 416 JO - Iraqi Journal of Science المجلة العراقية للعلوم SN - 00672904 23121637 AB - Due to the specific characteristic of porcelain, the insertion of Beryllium oxide has been studied. The basic materials and quantities were selected carefully. In this work, porcelain containing 32 wt% feldspar, 24 wt% quartz and 44 wt% clay was synthesized and beryllium oxide (BeO) (1 wt.%, 3 wt.%, 5 wt% and 7wt%) were add. The basic and new composition porcelain powders were uniaxially compacted into standard samples dimensions and fired at various sintering temperatures, 1100°C, 1300°C, and 1450°C then held for 2 hour in a furnace.The effects of sintering temperatures and beryllium oxide content on mechanical, electrical and structural properties were studied. The increasing of sintering temperature on the basic porcelain leads to an enhancement in bulk density and compressive strength. Basic porcelain which suffering lower sintering temperature (1300°C) introduces higher dielectric constant values in contrast with that suffering higher temperature (1450°C). The addition of BeO to the basic porcelain leads to decrease the bulk density and compressive strength. Porcelain with lower sintering temperature introduces higher έ values in contrast with higher temperature. The FTIR measurement show the existence of absorption at 800 cm-1 which attributable to Si-O-Si symmetrical stretching vibration band in all prepared samples. Band near 780 cm-l is attributed to the vibration of a beryllium atom moving in a tetrahedron of fixed oxygen atoms, while the absorption bands in the region 400-1500 cm-1 are due to the Be-O stretching and bending vibrations.

نظرا للاهمية الخاصة للخزف، تم دراسة تأثير اضافة اوكسيد البريليوم اليه. وقد تم اختيار المواد الأساسية والكميات بدقة. تم في هذا العمل تصنيع الخزف الذي يحتوي على 32٪ فلدسبار، 24٪ كوارتز و 44٪ من الطين وتم اضافة (1٪ ، 3٪ ، 5٪ و7٪) من أوكسيد البريليوم (BeO). وقد تم كبس مساحيق الخزف الأساسي و ذي المكونات الجديدة بطريقة الضغط الاحادي المحور للحصول على عينات قياسية الابعاد وتم حرق العينات بدرجات تلبيد مختلفة 1100م° ، 1300 م°، و1450 م° درجة مئوية لمدة ساعتين في الفرن. تمت دراسة تأثير درجات الحرارة ومحتوى أوكسيد البريليوم على الخواص الميكانيكية والكهربائية والهيكلية للخزف المصنع. لقد وجد ان زيادة درجة حرارة التلبيد للخزف الأساسي يؤدي إلى تحسين في الكثافة وقوة الانضغاط. الخزف الأساسي الذي عانى من درجة حرارة تلبيد أقل (1300 درجة مئوية) اعطى قيم ثابت عزل أعلى بالمقارنة مع تلك التي عانت من درجة حرارة تلبيد اعلى (1450 درجة مئوية). ان إضافة اوكسيد البريليوم إلى الخزف الأساسي أدى إلى تقليل الكثافة الظاهرية وقوة الانضغاط. الخزف الملبد بدرجة حرارة اقل أظهر قيم ثابت عزل έ اعلى بالمقارنة مع ارتفاع درجات الحرارة. أظهرت قياسات تحويلات فورير للاشعة تحت الحمراء في كل العينات المحضرة والملبدة حزمة امتصاص في 800 سم -1 والتي ترجع إلى حزمة اهتزاز الشد المتناظرة Si-O- Si. وتعزى الحزمة قرب 780 سم-1 إلى اهتزاز ذرة البريليوم المتحركة في رباعي الوجوه ذو ذرات الأوكسجين الثابتة الموقع، في حين أن حزم الامتصاص في المنطقة 400-1500 سم -1 تعود لاهتزاز الانحناء والشد لآصرة الـO- Be . ER -