@Article{, title={STATIC AND DYNAMIC ANALYSIS OF ASTIFFENED CYLINDER UNDER THE ACTION OF DIFFERENT LOAD CONDITIONS التحليل الاستاتيكي والديناميكي لاسطوانة مقواة تحت تاثير احمال مختلفة}, author={Dr. Hatem H. Obied1 Mahdi M. S. Shareef2 مهدي محمود شاكر أ.م.د. حاتم هادي عبيد}, journal={Iraqi journal of mechanical and material engineering المجلة العراقية للهندسة الميكانيكية وهندسة المواد}, volume={15}, number={4}, pages={256-271}, year={2015}, abstract={In this paper, the effect of different types of stiffeners on the cylindrical shell structure is presented. The stiffened shell models are examined under the action of static and dynamic excitations. Finite element models for the different stiffened cylindrical steel shell have been created by considering the helix angles and height of stiffeners, and a cantilever supported models are used. Additionally, the models are assumed to have a constant mass which is (4 kg) . All structure models have examined under action of static, harmonic and transient loads. Also the dynamic properties (natural frequencies) are computed for each FEMs. A concentrated load of the magnitude of (100 N) in three directions (x, y and z) is used in these structural analyses (static, harmonic and transient). This force is applying to the upper edge which is opposite the clamping edge . From these analyses, the best helix angle occurs at stiffener angle (90o), and the best height of stiffener that the modal analysis gives is (2 cm) and that gives by other analysis is (6.25 cm) . Finally, a comparison between experimental work of [M. Bagheri. and A. A. Jafari(2006)] and numerical part of the current paper has been occurred with a small percentage error between them.

في هذا البحث تم استعراض تأثير انواع مختلفة من عناصر التقوية على هيكل اسطواني رقيق. حيث تم اختبار النماذج المقواة سكونياً وحركيا. باستخدام طريقة العناصر المحددة تم بناء نماذج اسطوانية الشكل مقوات من الحديد الصلب مع الاخذ بنظر الاعتبار زاوية ميلان وارتفاع عناصر التقوية، و قد تم تثبيت النماذج من جهة وتركها حرة من الجهة الاخرى بالإضافة الى ثبوت الكتلة لكل النماذج المختلفة حيث كان مقدار الكتلة هو (4 كغم).ان كل النماذج تم اختبارها تحت تأثير الاحمال السكونية ، الترددية و الاحمال الانتقالية بالإضافة الى حساب الترددات الطبيعية لكل نموذج من نماذج العناصر المحددة، و الحمل المسلط هو عبارة عن حمل مركز ذو قيمة مقدارها (100 نت) سلط بثلاث اتجاهات (x, y and z) و قد سُلِط هذا الحمل عند الحافة العليا المقابلة لحافة التثبيت.من خلال تلك التحليلات التي تم استخدامها تبين ان افضل زاوية ميلان لعناصر التقوية هي (90 درجة) لكن افضل ارتفاع يعطيه التحليل الحر كان مقداره (2 سم) و (6.25 سم) تم الحصول عليه من التحليلات الاخرى.اخيراً تم اجراء مقارنة بين الجزء العملي للباحثين [M. Bagheri. and A. A. Jafari(2006)] والجزء النظري لهذا البحث للتأكد من صحة النتائج مع ظهور نسبة خطأ صغيرة بين البحثين.} }