@Article{, title={Experimental Investigation of Forced Convection Heat Transfer in Open Cell Copper Fins بحث تجريبي لحمل الحرارة القسري في زعانف النحاس الاسفنجي مفتوح الخلية}, author={Issam Mohammed Ali عصام محمد علي and Munther Abdullah Mussa منذر عبدالله موسى and Mustafa Mahdi Mustafa مصطفى مهدي مصطفى}, journal={Al-Nahrain Journal for Engineering Sciences مجلة النهرين للعلوم الهندسية}, volume={20}, number={1}, pages={272-280}, year={2017}, abstract={Recently, major part of convection heat transfer researches focus on increasing fins efficiency by increasing thermal performance for the same fin volume. Metal foam is a promising way to achieve this aim. Performance analysis has been carried out to investigate the heat transfer characteristics of copper fin foam samples. The samples have been compared with the solid metal fin heat transfer. A forced convection heat transfer had been applied to a four specimens. An electrical heater heats up the fins, which are subjected to a stream of the ambient air driven by a blower fan as heat dissipated. The heat flux had been fixed along the tests with three different air velocity used; the forced heat convection had been simulated. The pores density of copper fin foam is varied in the range of 10, 20 & 40 pores per inches (PPI). Thermal performance of copper fin foam has been evaluated in terms of average Nusselt number and thermal resistance of heat sinks. The increasing in the heat transfer rate and average Nusselt number when used metal foam has been found in the range of 36-133 % compare to solid copper. Furthermore, it has been proven that this increment reaches the maximum value for a given PPI even when raise the air velocity.

في الآونة الأخيرة، جزء كبير من الباحثين ركز اهتمامه على زيادة كفاءة الزعانف عن طريق زيادة الأداء الحراري لنفس حجم الزعنفة الاصلية. المعدن الاسفنجي أحد الطرق الواعدة لإنجاز هذا الهدف. تم اجراء تحليل أداء لبحث الخواص الحرارية لنماذج زعانف من النحاس الاسفنجي. هذه النماذج تم مقارنتها مع انتقال الحرارة في زعانف النحاس الصلد. انتقال حرارة بالحمل القسري تم تسليطه على أربعة نماذج. مسخن كهربائي سخن الزعانف التي كانت تخضع لتيار من الهواء المحيط مدفوع بواسطة مروحة منفاخ والذي يعتبر كمشتت للحرارة. الفيض الحراري تم تثبيته في كل التجارب وباستخدام ثلاث سرع للهواء، حمل الحرارة القسري تم تمثيله. فيض حراري ثابت تم تسليطه خلال التجارب مع سرع هواء معينة كمتغيرات حاكمة. كثافة المسام للنحاس كانت 10, 20, 40 مسامة بمربع البوصة. الأداء الحراري لزعنفة النحاس الاسفنجي تم حسابه من خلال معدل رقم نسيلت والمقاومة الحرارية لمشتت الحرارة. الزيادة في معدل انتقال الحرارة ومعدل رقم نسيلت عند استخدام المعدن الاسفنجي وجدت بحوالي مدى من %36 الى 133 % مقارنة بالمعدن الصلد. علاوة على ذلك، تم اثبات ان هذه الزيادة تصل لقيمة عظمى لكل قيمة من كثافة المسام ولا تتجاوزوها حتى بزيادة سرعة الهواء.} }