TY - JOUR ID - TI - Compatibility between Hydraulic and Mechanical Properties of Ceramic Water Filters توافق الخصائص الهيدروليكية والميكانيكية لمرشحات الماء الخزفية AU - Riyadh Z. Al Zubaidy رياض زهير الزبيدي AU - Mahmoud S. Al-Khafaji محمود صالح الخفاجي AU - Riyadh J. M. Al-Saadi رياض جاسم محمد السعدي PY - 2017 VL - 23 IS - 5 SP - 147 EP - 167 JO - Journal of Engineering مجلة الهندسة SN - 17264073 25203339 AB - In this paper, ceramic water filters were produced by using ten mixtures of different ratios of red clay and sawdust under different production conditions. The physical properties of these filters were tested. The production conditions include five press pressures ranged from 10 to 50MPa and a firing schedule having three different final temperatures of 1000, 1070, and 1100˚C. The tests results of the physical properties were used to obtain best compatibility between the hydraulic and the mechanical properties of these filters.Results showed that as the press pressure and the firing temperature are increased, the bulk density and the compressive and bending strengths of the produced filters are increased, while, the porosity and absorption are decreased. As the sawdust content is increased the bulk density and the compressive and bending strengths are decreased, while, the porosity and absorption are increased. High hydraulic conductivity is obtained at a firing temperature of 1070˚C when the sawdust content is less than 10%. Otherwise, it is increased as sawdust content and the firing temperature are increased. Filters made of mixture 92.5% red clay and 7.5% sawdust formed under a press pressure of 20MPa and a firing temperature of 1070˚C gave the best compatibility between hydraulic and mechanical properties. In this case, the hydraulic conductivity was 50mm/day, the compressive strength was 14MPa, and the bending strength was 10.8MPa.

هدف هذا البحث انتاج مرشحات ماء خزفية باستخدام عشر خلطات بنسب مختلفة من الطين الاحمر ونشارة الخشب كمضاف وتحت ظروف انتاج مختلفة وليتم فحص خواصها الفيزيائية. تضمنت ظروف الانتاج خمسة ضغوط للكبس تراوحت بين 10 و 50 ميكا باسكال وجدول للحرق بثلاث درجات نهائية مختلفة 1000 و 1070 و 1100˚م. استخدمت نتائج فحص الخواص الفيزيائية في تحديد افضل توافق بين الخواص الميكانيكية والهيدروليكية لهذه المرشحات. اشارت نتائج الاختبارات بان زيادة كل من ضغط الكبس وحرارة الحرق تؤدي الى زيادة كثافة ومقاومتي الانضغاط والانحناء للمرشحات المنتجة بينما تقل كل من المسامية والامتصاص لها. تقل كثافة ومقاومتي الانضغاط والانحناء للمرشحات المنتجة وتزداد كل من المسامية والامتصاص بزيادة محتوى نشارة الخشب. تم الحصول على أعلى ايصالية هيدروليكية عند درجة حرق مقدارها 1070˚م عندما يكون محتوى نشارة الخشب أقل من 10% وبخلاف هذه النسبة تزداد الايصالية الهيدروليكية بزيادة نسبة نشارة الخشب ودرجة الحرارة. وجد بان المرشحات المنتجة باستخدام خلطة مكونة من 92.5% من الطين الاحمر و7.5% من نشارة الخشب والمشكلة تحت ضغط كبس مقداره 20 ميكا باسكال ودرجة حرق مقدارها 1070˚م تعطي أفضل توافق بين الخواص الهيدروليكية والميكانيكية. وفي هذه الحالة كان مقدار الايصالية الهيدروليكية 50ملم/يوم ومقاومة الانضغاط 14 ميكا باسكال ومقاومة الانحناء 10.8 ميكا باسكال. ER -