TY - JOUR ID - TI - Design and Fabrication of evacuated tube solar thermal collector for domestic hot water تصميم وتصنيع مجمع الطاقة الشمسية الحرارية ذات الأنابيب المفرغة لتسخين الماء في المنازل AU - Dr. Alaa H. Shneishil علاء حسن شنيشل PY - 2016 VL - IS - 3 SP - 287 EP - 302 JO - Journal of College of Education مجلة كلية التربية SN - 18130380 AB - The objective of this research is to design and fabricate solar water heating system by Investment defective materials in Iraq for domestic sector applications in order to encourage national industry. Defective neon light tube with length 120 Cm and diameter 3 Cm has been used as an outer pipe. Copper pipe with length 125 Cm and diameter 1 Cm is placed inside the glass tube and close the space between them by circular shell that is used as an inner absorber material after painting it by black non brightness coating. The space between the outer glass tube and the inner copper pipe is evacuated by using small compressor. The evacuated tubes are connected from the upper side with insulated storage tank and from lower side with circulation pump. The evacuated tubes are placed in the focal line of reflective surfaces. The efficiency of the fabricated solar collector has been measured and compared with uninsulated storage tank which put in the same conditions. These measurements are done with and without reflective surfaces. The results indicated that the temperature of water in the evacuated tube with reflective surfaces reach to 59.5 °C while in the evacuated tube without reflective surfaces reaches to 44.3 °C. The temperature of water in the evacuated tube without circulation pump reach to maximum value which about 85.3 oC. This value is greater than that of the case with circulation pump.

الهدف من هذا البحث هو تصميم وتصنيع نظام الطاقة الشمسية لتسخين المياه باستثمار المواد التالفة في العراق لتطبيقات القطاع المحلي من أجل تشجيع الصناعة الوطنية. وقد استخدم أنبوب ضوء نيون تالف بطول 120 سم وقطر 3 سم كأنبوب الخارجي. وتم وضع أنابيب النحاس بطول 125 سم وقطرها 1 سم داخل الأنبوب الزجاجي وإغلاق المسافة التي تفصل بينهما بواسطة حلقة دائرية والتي يتم استخدامه كمادة امتصاص داخلية بعد طلاءه بمادة سوداء غير عاكسة. تم تفريغ المنطقة بين أنبوب الزجاج الخارجي وأنبوب النحاس الداخلي باستخدام ضاغط صغير . تم توصيل الأنابيب المفرغة من الجانب العلوي مع خزان معزول ومن الجانب السفلي مع مضخة التدوير. وضعت الأنابيب المفرغة في الخط البؤري للسطوح العاكسة. وقد تم قياس كفاءة مجمع الطاقة الشمسية المصنع ومقارنته مع خزان غير معزول موضوع في نفس الظروف. وتم هذا القياس مع وبدون السطوح العاكسة. أشارت النتائج إلى أن درجة حرارة المياه في الأنابيب المفرغة مع السطوح العاكسة تصل إلى °C 59.5 بينما الانبوب بدون السطوح العاكسة تصل إلى °C 44.3. درجة حرارة المياه في الأنابيب المفرغة بدون مضخة التدوير تصل إلى القيمة القصوى حوالي °C 85.3. هذه القيمة أكبر من حالة وجود مضخة التدوير. ER -