@Article{, title={EFFECT OF THE ADDITION OF STYRENE–BUTADIENE RUBBER LATEX ON THE WATER ABSORPTION AND COMPRESSIVE STRENGTH OF CRUMB RUBBER-MORTAR دراسة تأثير اضافة مطاط الستايرين-بيوتادين على امتصاصية الماء ومقاومة الانضغاط للملاط - مفروم المطاط}, author={Besma Mohammed Fahad and Ali Isam Mohsin}, journal={Journal of Engineering and Sustainable Development (JEASD) مجلة الهندسة والتنمية المستدامة}, volume={20}, number={1}, pages={194-205}, year={2016}, abstract={: In this research different mixes were prepared with Cement-Sand ratio (1:3) and Water- Cement (0.5) by weight. Four sets were prepared by partially or full replacing the sand with crumb rubber tire to fabricate the Crumb Rubber-Mortar (CRM) mixtures. The first two sets include fine crumb rubber with particles size (0.3-1 mm), The other set include coarse crumb rubber with particles size (1.18-2.36 mm).The third and fourth sets were prepared as the same first sets but with the addition of (7%) Styrene–Butadiene Rubber (SBR) latex by weight of cement. Each set was consist of different percentage of replacing the sand by crumb rubber (10,30,50,100%) by volume. Tests were conducted, including water absorption and compressive strength. Several results obtained before and after the addition of Styrene-Butadiene Rubber (SBR) which shows an increase in crumb rubber percentage cause decrease in compressive strength and water absorption; while as the density increases the compressive strength and water absorption increased before the addition of SBR. After the addition of SBR to the crumb Rubber-Mortar the compressive strength and water absorption are improved. In general fine crumb Rubber-Mortar have better properties than coarse crumb Rubber-Mortar.

تناول البحث تحضير خلطات مختلفة للملاط بنسبة وزنية (1:3 أسمنت- رمل) ونسبة الماء الى الاسمنت (0.5) , حيث حضرت اربع مجاميع وذلك باستبدال جزئي او كلي للرمل مع مطاط الاطارات المفرومة لتصنيع خلطات ملاط - مفروم المطاط (CRM). تضمنت المجموعتين الاولى والثانية مفروم اطارات بدون اضافة مطاط الستايرين-بيوتادين (SBR) احدهما بحجم جزيئي ناعم (0.3-1 mm) و الاخرى تضمنت مفروم اطارات خشن بحجم جزيئي (1.18-2.36 mm) .اما المجموعتين الثالثة والرابعة فحضرت بنفس مواصفات المجاميع الاولى ولكن بعد اضافة(7%) SBR من وزن الاسمنت. تم استبدال الرمل بمفروم المطاط (10,30,50,100%) استبدالاً حجمياً لكل المجاميع. الفحوصات التي اجريت تتضمن امتصاصية الماء ومقاومة الانضغاط. حيث تم الحصول على العديد من النتائج قبل وبعد اضافة (SBR) التي أظهرت ان الزيادة في نسبة المطاط تؤدي الى نقصان في امتصاصية الماء ومقاومة الانضغاط , في حين الزيادة في الكثافة تؤدي الى زيادة في امتصاصية الماء ومقاومة الانضغاط. بعد اضافة (SBR) الى ملاط - مفروم المطاط تم تحسين امتصاصية الماء ومقاومة الانضغاط. بصورة عامة فأن ملاط - مفروم المطاط الناعم يمتلك خواص افضل من ملاط - مفروم المطاط الخشن.} }