TY - JOUR ID - TI - Wear Characteristics of Al-Based Composite Material خواص المادة المركبة ذات اساس الالمنيوم AU - Iman M. Naemah ايمان محمد نعمة AU - Ekhlas Edan Kader اخلاص عيدان قادر AU - Khuder N. Abed خضر نجم عبد PY - 2018 VL - 14 IS - 1 - Part 1 SP - 129 EP - 140 JO - Academic Science Journal مجلة العلوم الاكاديمية SN - 83732222 25189255 AB - This research studies the wear characteristic of Al- based composite material. Stir casting technique was used to fabricate composite samples of Al-6061 and Al-6061 reinforced with different percentage ages (5%, 10%, 15% weight) of silicon carbide particles (SiC). Abrasive wear behavior of composite was studied by dry sliding pin on disc method. Different parameters were taken into consideration including, applied load, sliding speed, and weight percentage age of silicon carbide particles. Wear test-sliding distance ranged from 1044 m to 3123 m measured over different times (10 min, 20 min, and 30 min). Normal loads range from 10 N to 30 N, at sliding speeds of 1.74m/s. Specific wear rate was calculated considering weight loss calculation which was measured by using digital electronic balance (up to 0.01 g accuracy). The results show that by increasing the sliding speed and the applied load we get the highest wear rate in the aluminum alloy, while with the Al/SiC composite, the wear rate decreases with the increase of SiC percentage age. It was found that hardness increases simultaneously when SiC percentage age increases. The highest hardness in (AL- 15 wt. % SiC) was recorded.

في هذا البحث تمت دراسة خصائص البليان للمادة المركبة ذات اساس الالمنيوم.استخدمت طريقة الخلط والسباكة لصناعة نماذج المادة المركبة للالمنيوم وللالمنيوم المدعم باضافة كاربيد السليكون. تمت دراسة البليان بوجود سطح خشن وذلك خلال دراسة طريقة انزلاق العينة على قرص دوار اكثر صلادة منه. اخذت في هذا الاختبار عدة عوامل بعين الاعتبار منها الحمل المسلط، سرعة الانزلاق، وتاثير اضافة نسب متنوعة من كاربيد السليكون. سرعة انزلاق العينة تتراوح من 1044-3123 متر محسوبة لفترات زمانية متنوعة ومؤثرة(١٠-ـ٣٠ دقيقة). الاحمال العمودية المُسلطة تراوحت من 10ـ30 نيوتن وبسرعة انزلاق 1.47 متر بالثانية. تم احتساب معدل البليان باعتبار الوزن المفقود والذي يتم قياسه باستخدام ميزان حساس ذو دقة تصل الى( g0.01 (. اظهرت النتائج ان زيادة سرعة الانزلاق والحمل المُسلط ادت الى زيادة معدل البليان في معدن الالمنيوم. بينما في المادة المركبة معدل البليان يقل بزيادة نسبة كربيد السليكون. لوحظ ان الصلادة تزداد. بزيادة نسبة كربيد السليكون وان اعلى قيمة له كانت عند نسبة 15% كربيد السليكون ER -