TY - JOUR ID - TI - Effect of Underground Corrosion on the Buckling of Al Alloy 6061 - T4 Columns under Increasing Load تأثير التآكل تحت الأرض على الانبعاج الجانبي لأعمدة سبيكة الالمنيوم T4-6061 - تحت تأثير زيادة الاحمال AU - Ali Yousuf Khenyab علي يوسف خ ن ياب AU - Hussein Fadhil Ajaj حسين فاضل عجاج AU - Rawa Ahmed Helal رواء احمد هلال PY - 2018 VL - 21 IS - 3 SP - 417 EP - 427 JO - Al-Nahrain Journal for Engineering Sciences مجلة النهرين للعلوم الهندسية SN - 25219154 25219162 AB - This research deals with the extent to which corrosion affects the behavior of buckling for 6061-T4 aluminum alloy under increasing compressive dynamic loads. Two types of columns, long, and intermediate were used.1% of the length column is the allowable lateral deflection. This is called the critical buckling of the columns. For the purpose of calculating the critical deflection, a digital dial gauge was used and set at a distance of 0.7 of column length from the fixed end condition for the column. The experimental analysis revealed that the corrosion time negatively affects the mechanical properties of materials such as the corroded specimens of 60 days (The least time to observe the corrosion of aluminum in the soil) which have approximately 2.7% reduction in ultimate strength compared with the non-corroded specimen. Increasing the corrosion time reduces the critical load such as the maximum reduction will be 4.24% in critical buckling load for 60 days’ corrosion time. The results obtained were experimentally compared with the theoretical formulas of the Perry-Robertson and Euler-Johnson formula with the results of the ANSYS. It was found that the Perry-Robertson formula has a good agreement with the experimental results with a safety factor of 1.2, while the Euler-Johnson formula agreed with the experimental results taking a safety factor of 1.5. The ANSYS results showed a good agreement between the measured and calculated values by taking 1.1 factor of safety.

يتناول هذا البحث مدى تأثير التآكل على سلوك الانبعاج الجانبي لسبيكة الالمنيوم (T4-0606) تحت زيادة احمال الضغط الديناميكية. تم استخدام نوعين من الأعمدة، طويلة و متوسطة. 6٪ من طول العمود هو الانحراف الجانبي المسموح به. ولغرض حساب الانحراف الأولي، استخدم جهاز digital) dial gauge) وتم تثبيت المقياس على بعد 6.0 من طول العمود من جهة التثبيت. وأظهر التحليل التجريبي أن زيادة وقت التآكل يؤثر سلبا على الخواص الميكانيكية للمعادن . فكان معدل النقصان في اقصى اجهاد للعينات المدفونة 06 يوما (اقل وقت لملاحظة وقت التأكل في التربة) هو ٪ 7.0 مقارنتا مع العينات غير المتآكلة ، كما ان زيادة وقت التآكل يقلل من الحمل الحرج مثل أقصى نقصان كان ٪ 4.74 في حمل الانبعاج الحرج لعينات مدفونة 06 يوما في التربة. تم مقارنة النتائج التي تم الحصول عليها تجريبيا مع الصيغ النظرية لبيري -روبرتسون و صيغة يولر-جونسون ومع نتائج برنامج ANSYS)). وقد وجد أن صيغة بيري-روبرتسون أبدت توافق جيد مع النتائج التجريبية مع عامل أمان 6.7 ، وكانت صيغة يولر -جونسون مناسبة للنتائج التجريبية مع الاخذ بعامل أمان 6.1. نتائج برنامج ANSYS)) أظهرت توافق جيد بين القيم المقاسة والمحسوبة مع أخذ عامل امان 1.1 ER -