@Article{, title={Estimating of Pore Pressure Gradient in Lower Fars Formation تقدير تدرج الضغط المسامي في تكوين الفارس الاسفل}, author={Neaam F. Hussain and Faleh H. M. Al Mahdawi}, journal={Iraqi Journal of Chemical and Petroleum Engineering المجلة العراقية للهندسة الكيمياوية وهندسة النفط}, volume={19}, number={4}, pages={29-38}, year={2018}, abstract={In petroleum industry, the early knowledge of “pore pressure gradient” is the basis in well design and the extraction of these information is more direct when the pore pressure gradient is equal to normal gradient; however, this matter will be more complex if it deviate from that limit which is called “abnormal pore pressure”, if this variable does not put in consideration, then many drilling problems will occur might lead to entire hole loss. To estimate the pore pressure gradient there are several methods, in this study; Eaton method’s is selected to extract the underground pressure program using drilling data (normalized rate of penetration) and logs data (sonic and density log). The results shows that an abnormal high pressure is observed in Lower Fars formation started from Mb5 member as a transition zone and increase gradually until reach the Mb4 member and continuous to Mb3 and Mb2 then begin to decrease from Mb1 which is consider a transition zone between high pore pressure zone and sub-pressure zone represented by Jeribe-Euphrate and Upper Kirkuk formations and back to normal pore pressure at Middle-Lower Kirkuk formation. The dc-exponent method has been selected in estimating pore pressure gradient and considers the best one compared with logs data methods.

في الصناعة البترولية ، تشكل المعرفة المبكرة عن "تدرج ضغط المسام" الأساس في تصميم البئر ;يكون استخلاص هذه المعلومات في أكثر مباشرة عندما يكون تدرج الضغط المسامي مساويا للتدرج الطبيعي. ومع ذلك ، ستكون هذه المسألة أكثر تعقيدًا إذا كانت تنحرف عن ذلك الحد وهذا يسمى "ضغط المسام غير الطبيعي" ، إذا لم يضع هذا المتغير في الاعتبار ، عندها سيحدث العديد من مشاكل الحفر قد يؤدي إلى فقدان كامل للبئر. لتقدير التدرج ضغط المسام هناك عدة طرق ، في هذه الدراسة ؛ يتم اختيار طريقة إيتون لاستخراج برنامج الضغط تحت الأرض باستخدام بيانات الحفر (مؤشر الحفرdc-exponent ) وبيانات السجلات (سجل الصوت والكثافة). تظهر النتائج أنه لوحظ ارتفاع في تدرج الضغط المسامي يبدأ من تكوين الفارس الاسفل ( Lower Fars) يبدأ من المنطقه Mb5 كمنطقه انتقاليه وتتزايد تدريجيا حتى يصل الى Mb4 التي تعتبر منطقة الضغط العالي في ذلك التكوين وتستمر الى Mb3 و Mb2 ثم يبدأ الضغط بالتناقص من منطقة Mb1 التي تعتبر منطقة انتقاليه بين منطقة الضغط العالي ومنطقة الضغط المنخفض المتمثله بتكوين Jeribe-Euphrate) ) و (( Upper Kirkuk ومن ثم تعود الى منطقة الضغط الطبيعي في تكوين (Middle-Lower Kirkuk). ان طريقة مؤشر الحفر (dc-exponent) تم اختيارها في تخمين تدرج الضغط المسامي وتم اعتبارها أفضل طريقه بالمقارنه مع الطرق الاخرى المتمثله ببيانات المجسات.} }