@Article{, title={Impact of Holes on The Buckling of RHS Steel Column}, author={Najla'a H. AL-Shareef}, journal={Journal of University of Babylon مجلة جامعة بابل}, volume={26}, number={5}, pages={209-226}, year={2018}, abstract={This study presented an experimental and theoretical study on the effect of hole on the behavior of rectangular hollow steel columns subjected to axial compression load. Specimens were tested to investigated the ultimate capacity and the load- axial displacement behavior of steel columns.In this paper finite element analysis is done by using general purpose ANSYS 12.0 to investigate the behavior of rectangular hollow steel column with hole. In the experimental work, rectangular hollow steel columns with rounded corners were used in the constriction of the specimens which have dimensions of cross section (50*80)mm and height of (250 and 500)mm with thickness of (1.25,4 and 6)mm with hole ((α*80)*80)mm when α is equal to (0.2,0.4,0.6 and 0.8). Twenty four columns under compression load were tested in order to investigate the effect of hole on the ultimate load of rectangular hollow steel column. The experimental results indicated that the typical failure mode for all the tested hollow specimen was the local buckling. The tested results indicated that the increasing of hole dimension leads to reduction in ultimate loads of tested column to 75%. The results show the reducing of load by 94.7% due to decreasing the thickness of column while the hole size is constant (0.2*80*80). The buckling load decreases by 84.62% when hole position changes from Lo=0.25L to 0.75L. Holes can be made in the middle of column with dimension up to 0.4 of column's length. The AISC (2005) presents the values closest to the experimental results for the nominal yielding compressive strength.The effect for increasing of slendeness ratio and thickness to area ratio(t/A) leading to decreacing the critical stresses and the failure of column with large size of hole and (t/A) ratio less than 0.74% was due to lacal buckling while the global buckling failure was abserve for column with small size of hole and (t/A) ratio above than 0.74%. The compersion between the experimental and theoretical results showed a reasonable agreement and the difference was in the range (1.28-14.88)%.

فيهذاالبحث تم اجراءدراسة عملية ونظرية لتأثير الفتحات في تصرف الاعمدة الفولاذيةالمستطيلةالمجوفةالمعرضة لأحمال ضغط محورية. تم فحص عينات لدراسة التحمل الاقصى وتصرف حمل-أزاحات محورية للأعمدة الفولاذية.في هذا البحث تم استخدام نظرية العناصر المحددة المتمثلة ببرنامج ANSYS 12.0 لتحليل تصرف الاعمدة المستطيلة المجوفة مع فتحات. في الجزء العملي استعملت اربعة وعشرون نموذج من الاعمدة الفولاذية المستطيلة المجوفة بزوايا مدورة الذي له ابعاد مقطع50*80))ملم وارتفاع 250,500)) ملم و بسمك (1.25,4 and 6)ملم مع ابعاد حفرة ((80*α)*80) ملم بحيث ان αمساوية الى 0.2,0.4,0.6 and 0.8)) . تم فحص اربعة وعشرون من الاعمدة الفولاذية تحت حمل انضغاط من اجل التحقيق في تأثير الحفرة في المقاومة القصوى للأعمدة المستطيلة المجوفة. أظهرت النتائج العملية أن طريقة الفشل النموذجية لجميع العينات المجوفة المختبرة كانت التواء المحلي. وأظهرت النتائج التي تم اختبارها أن زيادة ابعاد الحفرة يؤدي إلى الحد من الحمل الاقصى للعمود يصل إلى 75%. وأظهرت النتائج تقليل الحمل بنسبة 94.7%بسبب انخفاض سمك العمود بينما يكون حجم الثقب ثابتا. ينخفض الحمل التواء بنسبة 84.62%عندما يتغير موفع الحفرة من 0.25L إلى 0.75L. يمكن إجراءالحفرة في منتصف العمود مع بعد يصل إلى 0.4 من طول العمود. و AISC(2005) يعرض القيم الأقرب إلى النتائج العمليةلمقاومة خضوع الانضغاط. أدى تأثير زيادة نسبة الانحناء ونسبة السمك إلى مساحة (t / A) مما أدى إلى خفض مقومة الانضغاط الحرجة وفشل العمود مع حجم كبير من الحفرة و (t / A) نسبة أقل من 0.74%ويرجع ذلك إلى الانبعاج المحلي في حين أن فشل الإبزيم العالمي كان معتمدا للعمود مع حجم صغير من الحفرة و (t / A) نسبة فوق 0.74%. وأظهرت النتائج وجود اتفاق معقول بين النتائج العملية والنظرية وكان الفرق يتراوح بين(1.28-14.88)%.} }