@Article{, title={Recovery of Copper from Copper Slag by Hydrometallurgy Method, from Iraqi Factories Waste}, author={Bahaa Sami Mahdi and Asaad Hasan}, journal={Journal of University of Babylon مجلة جامعة بابل}, volume={26}, number={7}, pages={179-199}, year={2018}, abstract={In this research, the recovery of copper from copper slag is investigated using hydrometallurgy method. Slag samples were taken from Al-Shaheed State Company. The results of the chemical analysis showed that the slag contained 11.4% of copper. The recovery process included two stages; the first stage is leaching using diluted sulfuric acid. The most important variables that effect on the leaching process was studied, such as acid concentration, hydrogen peroxide adding, particle size, liquid to solid, stirring speed and leaching time by changing the condition and the stabilizing of other factors at room temperature. The second stage is precipitation of copper from leaching solution by zinc powder with different weights and times, at room temperature and 1.5 PH value.The results of the first stage manifested that about 99.7% of the copper have been dissolved at the following operational conditions: 50% acid concentration, 5 ml hydrogen peroxide adding, particle size (-75+53) micron, 1:10 liquid to solid, 500 rpm stirring speed and 25 min of leaching time. The highest percentage of copper precipitation in the second stage was 99.8% when added 3gm zinc powder at 20 min.The XRD result revealed that the predominant phase was pure copper. The results of EDS exhibited that a few percentage of oxygen appeared with copper powder. The final of copper recovery ratio was 99.3% with 99.2% purity.

في هذا البحث تم دراسة استرجاع النحاس من خبث النحاس باستخدام الطريقة المائية. تم جلب نماذج العينيات من شركة الشهيد العامة. اظهرت نتيجة التحليل الكيميائي للنموذج ان الخبث يحتوي على % 11.4 من معدن النحاس . ان عملية استرجاع النحاس تضمنت مرحلتين: المرحلة الاولى هي عملية النض باستخدام حامض الكبريتيك المخفف.تم دراسة اهم العوامل المؤثرة على عملية النض مثلا : تركيز الحامض، تأثير اضافة بيروكسيد الهيدروجين، الحجم الحبيبي، نسبة السائل الى الصلب، سرعة التحريك ووقت عملية النض عن طريق تغير عامل مع تثبيت العوامل الاخرى عند درجة حرارة الغرفة. المرحلة الثانية كانت عملية ترسيب النحاس من سائل النض النهائي بواسطة مسحوق الزنك باستخدام اوزان واوقات مختلفة عند درجة حرارة الغرفة ايضا، تم تثبيت درجة حامضية محلول بقيمة 1.5. نتائج تجارب المرحلة الاولى بينت ان اعلى نسبة اذابة للنحاس وصلت الى 99.7 % تحت الظروف المثالية التالية: (50% تركيز الحامض، اضافة 5 مل من بيروكسيد الهيدروجين،الحجم حبيبي (53+75-)، نسبة السائل الى الصلب 1:10 ، سرعة التحريك 500 دورة بالدقيقة و بزمن مقداره 25 دقيقة.نتائج تجارب المرحة الثانية سجلت اعلى نسبة ترسيب النحاس والتي بلغت 99.8% بعد اضافة 3 غرام من مسحوق الزنك في غضون 20 دقيقة. بينت نتائج الفحص بحيود الاشعة السينية ((XRD للمنتج النهائي ان الطور السائد هو طور النحاس النقي فقط اما نتائج الفحص بمطيافية تشتت طاقة الاشعة السينية (EDS) سجلت ظهور نسبة قليلة من الاوكسجين مع معدن النحاس المترسب. بلغت نسبة استرجاع النحاس النهائي 99.3% بنقاوة وصلت الى 99.2%.} }