TY - JOUR ID - TI - Improving the Physical and Mechanical Properties of Fireclay Refractory Bricks by Added Bauxite تحسين الخواص الفيزيائية والميكانيكية لطابوق الحراري بإضافة البوكسايت AU - Sarmad Imad سرمد عماد ابراهيم AU - Nahedh Mahmud Ali ناهض محمود علي AU - Tamara Wahid Abood تمارة وحيد عبود PY - 2019 VL - 25 IS - 4 SP - 18 EP - 28 JO - Journal of Engineering مجلة الهندسة SN - 17264073 25203339 AB - In this study, the investigation of Local natural Iraqi rocks kaolin with the addition of different proportions of bauxite and its effect on the physical and mechanical properties of the produced refractories was conducted. Kaolin/bauxite mixture was milled and classified into various size fractions, the kaolin (less than 105 μm) and the bauxite (less than 70μm). The specimens were mixed from kaolin and bauxite in ranges B1 (95+5)%, B2 (90+10)%, B3(85+15)%, and B4 (80+20)% respectively. The green specimens were shaped by the semi-dry method using a hydraulic press and a molding pressure of 7 MPa with the addition of (9-12) %wt. of PVA ratio. After molding and drying, the specimens were fired at (1100, 1200 and 1300) °C. Physical properties (density, porosity, water absorption) and mechanical properties (indirect tensile strength and hardness) were measured for all the prepared samples. The results showed that the porosity was increased and the density was decreased, such increase and decrease affected on to the mechanical properties for refractory. The highest values of indirect tensile strength and hardness were obtained at 20% Bauxite at 1300 °C (0.85386 MPa, 1411Kg / mm²) respectively.

في هذا البحث تم فحص الكاولين كالصخور العراقية الطبيعية المحلية مع إضافة نسب مختلفة من البوكسايت و دراسة تأثيرها على الخواص الفيزيائية والميكانيكية للحراريات المنتجة ،تم طحن خليط الكاؤلين / البوكسايت بحجوم حبيبية معينه ,الكاؤلين (أقل من 105 ماكرون) والبوكسايت (أقل من70) ماكرون . تم خلط العينات بنسب وزنيه معينه كالأتي B1 (95 + 5)٪وB2 (90 + 10)٪وB3 (85 + 15)٪ و B4 (80 + 20)٪ على التوالي. وشكلت العينات بالطريقة شبه الجافة باستخدام المكبس الهيدروليكي بضغط 7 ميكا باسكال بإضافة محلول بوليمري بنسب وزنيه من(9-12)% من وزن العينة وتم تجفيف العينات لمده 9ساعات وتلبيد العينات بدرجات حرارية معينة (1100,1200,1300) ºم . تم فحص الخواص الفيزيائية (الكثافة والمسامية وامتصاص الماء) والخصائص الميكانيكية (مقاومة الشد غير المباشرة والصلادة) لجميع العينات. وأظهرت النتائج زيادة المسامية الظاهرية ونقص الكثافة الحجمية يؤثر على خصائص الميكانيكية للحراريات. وتم حصول على اعلى قيم مقاومة الشد غير مباشرة والصلادة في العينة الحاوية على 20% بوكسايت عند درجة حرارة تلبيد 1300مº(0.85386 MPa, 1411Kg/mm²) على التوالي . ER -