@Article{, title={Transmission (2Gbps) over optical fiber cable by using radio over fiber and wavelength division multiplexing techniques إرسال (2Gbps) عبر كابل الألياف الضوئية باستخدام تقنيات الراديو عبر الألياف ومضاعفة تقسيم الطول الموجي}, author={Humam Husseinˡ همام حسين1 and Dogu Cagdas Atilla1 ، دوغو جاغداش اتلا1 and Essa Essa2 عيسى عيسى2 and Cagatay Aydin1 جاغتاي ايدن1}, journal={Tikrit Journal of Pure Science مجلة تكريت للعلوم الصرفة}, volume={24}, number={5}, pages={115-123}, year={2019}, abstract={In recent years, there has been a growing and continuous demand for great (data rates) beyond existing wired and wireless networks. Radio-over-Fiber technology is considered as an efficient and practical solution for providing broadband wireless. In this paper, many techniques are used to implement a system that has the capability to provide a great bit rate, broadband bandwidth, and minimum cost. So Radio-over-Fiber technology was used to modulate the light with radio-signal and transmission the signals through an optical fiber cable. Wavelength-Division-Multiplexing technique was used to send many signals through the same link, and Subcarrier Multiplexing-Amplitude Shift keying as a modulation format. 2Gpbs separate on two channels was transmitted on Single-Mode Fiber. The average results obtained from our experience was as follows: maximum Q factor average = 4.9712925, minimum BER average = 3.63*10-7, total power average (dBm) = -51.1502, the OSNR average (dB) = 52.085 for channel_1. The results of channel_2 were: maximum Q factor average = 5.5901325, minimum BER average = 1.26*10-8, total power average (dBm) = -46.60135, the average of optical signal-to-noise ratio (dB) = 54.65. All the average result that has from our simulation was very good and acceptable. The simulation and performance test of our experience was done using Optisystem 7.0.

في السنوات الأخيرة، كان هناك طلب متزايد ومستمر لمعدلات بيانات كبيرة تتجاوز الشبكات السلكية واللاسلكية القائمة. تعتبر تقنية الراديو عبر الألياف حلاً فعالاً وعمليًا لتوفير اتصال لاسلكي واسع النطاق. في هذه الورقة، يتم استخدام العديد من التقنيات لتنفيذ نظام لديه القدرة على توفير معدل بت كبير، وعرض نطاق عريض النطاق، وبأقل تكلفة. تم استخدام تقنية لتعديل الضوء مع الإشارة اللاسلكية ونقل الإشارات عبر كبل الالياف الضوئية. كما استخدمت تقنية مضاعفة تقسيم الطول الموجي لإرسال العديد من الإشارات عبر نفس الوصلة، تعدد الإرسال الفرعي- تضمين إزاحة السعة استخدم كنسق تشكيل. تم نقل (2Gpbs) منفصلة على قناتين عبر الألياف أحادية النمط. كان متوسط النتائج التي تم الحصول عليها من تجربتنا كما يلي: كان متوسط إجمالي الطاقة الخارجة 51.1502-(dBm) ، وكان الحد الأقصى لمتوسط عامل الجودة 4.9712925، وكان متوسط BER الأدنى (3.63*10-7)، وكان متوسط OSNR 52.085 (dB). في الإشارة الثانية، كانت النتيجة كما يلي: كان متوسط إجمالي الطاقة الخارجة 46.60135- (dBm)، والحد الأقصى لمتوسط عامل الجودة 5.5901325، وكان متوسط BER الأدنى (1.26*10-8) ، ومتوسط OSNR كان dB) 54.65). كل النتائج المتوسطة التي حصلنا عليها من المحاكاة جيدة جدًا ومقبولة. تم إجراء اختبار المحاكاة والأداء على تجربتنا باستخدام برنامج Optisystem 7.0.} }