TY - JOUR ID - TI - Development of High Performance (Mechanical and Wear Properties) of AA 6061-Hybrid Nano Composites Via Liquid Metallurgy Route تطوير الاداء العالي للخواص الميكانيكية والترايبولجية للمركب النانوي الهجين لسبيكة المنيوم 6061 بواسطة السباكة المتحركة AU - Hussain J. M. Al-Alkawi حسين جاسم محمد العلكاوي AU - Abduljabbar Owaid Hanfesh عبد الجبار عويد حنفيش AU - Saja Mohammed Noori Mohammed Raouf سجى محمد نوري محمد رؤوف PY - 2019 VL - 22 IS - 2 SP - 143 EP - 150 JO - Al-Nahrain Journal for Engineering Sciences مجلة النهرين للعلوم الهندسية SN - 25219154 25219162 AB - This research is devoted to study the influence of different weight percent concerning to the additions of Ti and Cu on mechanical and tribological properties of AA6061. The composite materials consist of different weight percentage of Ti (0.2, 0.4, and 0.6) wt% and constant weight percentage of Cu (0.2) wt% which were fabricated by liquid metallurgy route technique. Microstructural characterization and phases have been examined by using SEM (scanning electron microscopic).SEM examination showed uniform distribution of nano Ti and Cu in AA6061. The consequences of mechanical tests demonstrated clear enhancement in mechanical properties, such as ultimate tensile strength, yield strength, young modulus, ductility% and hardness at additive percentage of 0.4% Ti+0.2%Cu nano particles incorporated into molten AA6061. Percentage of enhancement ultimate tensile strength is about 73.3%, yield strength about 82.7%, young modulus is about 21.2%, the Vickers hardness about 42.6% and the decreasing in ductility was about 25.2% compared with the metal matrix (AA6061). The wear rate test was performed by using pin on disc rig for both hybrid nano composite and base metal (AA6061) under various loads (10,15and 20) N with sliding speed (1.282) m/sec at a (10) min’s time. The results showed a decrease in wear rate at 0.4%Ti+0.2%Cu compared with the base metal (AA6061). Improvement percentage of wear rate is about 105% at 20 N load.

اتجه البحث الحالى الى دراسة تأثير نسب وزنية مختلفة للمواد نانوية Ti,Cu بأضافتها الى سبيكة الاساس على الخواص الميكانيكية والترابولجية وتداخل التأكل الكيمياوي الكلالي والموصفات الكهربائية لسبيكة المادة الاساس حيث كان المركب النانوي يحتوي على قيم مختلفة لTiوهي 0.6%,0.4%,0.2% مع ثابت النسبة الوزنية لCu ب .0.2% وتم تصنيع النماذج بطريقة السباكة بالتحريك تم فحص التركيب المجهري بأستخدام المجهر الضوئي والمسحي الالكترونيSEM حيث ان فحص SEM اعطى توزيع منتظم للTi وCu في سبيكة الالمنيوم 6061. الاختبارات الميكانيكة التي اجريت اعطت بشكل واضح تحسن في المواصفات الميكانيكية كمقاومة الشد العظمى واجهاد الخضوع ومعامل يونك والمطيليه والصلادة للتراكيب النانوية، فكانت افضل مواصفات اعطاها هي التركيب النانوي 0.4%Ti+0.2%Cu حيث اعطى نسبة تحسن لمقاومة الشد العظمى حوالي 73.3% واجهاد الخضوع حوالي 82.7% ومعامل يونك 21% وصلادة فيكر حوالي 42.6%وانخفاض في المطيلية حوالي 25.2% مقارنة مع المادة الاساس. تم انجاز فحص معدل البلى بأستخدام جهاز القرص والدبوس للتركيب النانوي الثنائي لتقوية النانو والمعدن الاساس (AA6061 ) تحت عدة احمال (10,15,20 N ) بسرعة m/sec1.282 وبزمن min10 .أوضحت النتائج نقصان في معدل البلى لحالة التركيب النانوي 0.4%Ti+0.2%Cu مقارنة مع المعدن الاساس وأعطت تحسن بمعدل البلى مقداره %105عند الحمل N20 . ER -