TY - JOUR ID - TI - Demulsification of Water in Iraqi Crude Oil Emulsion كسر استحلاب المياه في مستحلب النفط الخام العراقي AU - Zenah Hani Maddah AU - Tariq Mohammed Naife PY - 2019 VL - 25 IS - 11 SP - 37 EP - 46 JO - Journal of Engineering مجلة الهندسة SN - 17264073 25203339 AB - Formation of emulsions during oil production is a costly problem, and decreased water content in emulsions leads to increases productivity and reduces the potential for pipeline corrosion and equipment used. The chemical demulsification process of crude oil emulsions is one of the methods used for reducing water content. The demulsifier presence causes the film layer between water droplets and the crude oil emulsion that to become unstable, leading to the accelerated of water coalescence. This research was performed to study the performance of a chemical demulsifier Chimec2439 (commercial) a blend of non-ionic oil-soluble surfactants. The crude oils used in these experiments were Basrah and Kirkuk Iraqi crude oil. These experimental work were done using different water to oil ratio. The study investigated the factors that have a role in demulsification processes such as the concentration of demulsifier, water content, salinity, pH, and asphaltene content. The results showed in measuring the droplet size distribution, in Basrah crude oil, that the average water droplet size was between (5.5–7.5) μm in the water content 25% while was between (3.3-4) μm in the water content 7%. The average water droplet size depends on the water content, and droplet size reduced when the water content of emulsion was less than 25%. In Kirkuk crude oil, in water content of 7%, it was between (4.5-6) μm, while in 20%, it was between (4-8) μm, and in 25% it was between (5-8.8) μm. It was found that the rate of separation increases with increasing concentration of demulsifier. For Basrah crude oil at 400ppm the separation was 83%, and for Kirkuk, crude oil was 88%. The separation of water efficiency was increased with increased water content and salt content. In Basrah crude oil, the separation rate was 84% at a dose of salt of 3% (30000) ppm and at zero% of salt, the separation was70.7%. In Kirkuk crude oil, the separation rate was equal 86.2% at a dose of salt equal 3% (30000) ppm, and at zero% of salt, the separation 80%.

ان تشكيل المستحلبات خلال إنتاج النفط هو مشكلة مكلفة، ويؤدي انخفاض محتوى الماء في مستحلبات الزيت الخام إلى زيادة الإنتاجية وتقليل احتمال تآكل خطوط الأنابيب والمعدات المستخدمة. يعتبر كسر الاستحلاب الكيميائي لمستحلبات النفط الخام إحدى طرق لتقليل المحتوى المائي. وجود المستحلب يسبب طبقة رقيقة بين مستحلب النفط الخام وقطرات الماء لتصبح غير مستقرة مما يؤدي إلى تسارع اندماج قطرات الماء. تم إجراء هذا البحث لدراسة أداء المستحلب الكيميائي Chimec2439 (تجاري) وهو مزيج من مواد سطحية قابلة للذوبان وغير أيونية. كانت عينتا النفط الخام العراقية المستخدمة في هذه التجارب هي نفط خام البصرة وكركوك. وقد تمت هذه التجارب باستخدام نسب مختلفة من المياه إلى النفط. تناولت الدراسة العوامل التي لها دور على عملية الاستحلاب مثل تركيز الكاسر ودرجة الحموضة والملوحة ومحتوى الماء ومحتوى الأسفلت. أظهرت النتائج في قياس حجم القطيرات في نفط خام البصرة، أن متوسط حجم قطيرات الماء كان بين (5.5 - 7.5) ميكروميتر في محتوى الماء 25٪، بينما كان بين (3.3-4) ميكروميتر في محتوى الماء 7٪. انخفض متوسط حجم قطرة الماء بشكل ملحوظ عندما كان محتوى الماء للمستحلب أقل من 25 ٪. في مستحلب نفط خام كركوك عندما كان في محتوى الماء 7٪ كان بين (4.5-6) ميكرومتر، وفي 20٪ كان بين (4-8) ميكرون، وفي 25٪ كان بين (5-8.8) ميكرون. وقد وجد أن معدل الفصل يزداد بزيادة تركيز المستحلب، في نفط خام البصرة عند تركيز 400 جزء في المليون كان الفصل 83٪، وفي نفط خام كركوك كان اعلى فصل 88٪. وأيضا زاد فصل المياه مع زيادة محتوى الماء ومحتوى الملح، في نفط البصرة كان معدل الفصل 84٪ عند جرعة من الملح يعادل 3٪ (30000) جزء في المليون، وعند صفر٪ من الملح كان الفصل 70.7٪، في نفط كركوك الخام كان معدل الفصل 86.2٪ عند جرعة الملح يساوي 3 ٪ (30000) جزء في المليون، عند صفر ٪ من الملح كان الفصل 80 ٪. ER -