TY - JOUR ID - TI - Dry Sliding Wear Characteristics of EN 24 Steel Hardened by ND: YAG Laser AU - Ihsan AlNaimi PY - 2019 VL - 27 IS - 3 SP - 84 EP - 91 JO - Journal of University of Babylon مجلة جامعة بابل SN - 19920652 23128135 AB - The aims of this investigation is to survey influence of ND:YAG Laser surface treatment of dry sliding wear features of EN 24 steel, which is medium carbon low alloy steel.Many parts of automotive, railways, marine and electric power generators are made from this alloy with distinctive properties as high strength and good wear resistance.According to ASTM G99 standards, length and diameter of the samples were(2 and 1) cm prepared by lathe machining. The prepared specimens were heat treated by using pulse ND: YAG Laser of 1064 nm wavelengthand 6 Hz frequency with different energies as 500, 750 and 1000 mJ for 10 pulses. Whilst, wear inspect with dry slipping was carried out in pin–on–disc mechanism through changing loads and times from 5, to 25 N and 5 to 30 min in 5 intervals respectively.In addition, roughness and microhardness examinations were performed for the samples as received and after wear test. Photomicrographs were taken for the samplesbefore, after surface Laser treatment, before, and after wear test.Results obtained increasing in hardness with improving in wear resistance. Surface roughness of treated specimenswith 1000 mJ was more than with 500 and 750 mJ energies.

أهداف هذا البحث هي دراسة تأثير المعاملة السطحية بالليزر نيديميوم – ياك على خصائص البلى الانزلاقي الجاف للفولاذ EN 24 الذي هو عبارة عن سبيكة فولاذ متوسط الكربون منخفض السبائكية. وهي تستخدم في العديد من التطبيقات التي تتطلب مقاومة عالية ومقاومة بلى مثل بعض أجزاء المركبات، ســكك الحديد، مجالات البحرية ومولدات الطاقة الكهربائية. تم تحضير العينات بالتشـــغيل علـى المخرطة لقياس 2 سم طول و1 سم قطر بموجب المواصفة القياسية ASTM G99. تمت معاملة العينات المحضرة حرارياً باستخدام الليزر نيديوم – ياك النبضي بطول موجي 1064 نانومتر، وبتردد لمنظومة الليزر 6 هيرتز مع طاقات مختلفة 500،750،و1000 ملي جول لعشر نبضات. بينما أجري اختبار البلى الانزلاقي الجاف باستخدام تقنية المسمار– على– القرص بتغيير الأحمال والزمن بمقدار 5 إلى 25 نيوتن و5 إلى 30 دقيقة على التوالي وبخمسة فترات. كذلك أجريت اختبارات الصلادة الدقيقة وفحص الخشونة للعينات قبل وبعد اختبار البلى. وتم أخذ صور مجهرية للعينات قبل وبعد المعاملة السطحية بالليزر وأيضا قبل وبعد اختبار البلى. أظهرت نتائج هذا البحث تحسن مقاومة البلى وزيادة الصلادة. خشونة السطح للعينات المعاملة بـ 1000 ملي جول هي أكثر مما هو عليه للطاقات 500 و750 ملي جول. ER -