TY - JOUR ID - TI - Study the Influence of Gas Pressure on the Tensile Behavior of TIG Stainless Steel Sheets AU - Samir Ali Amin Al-Rabii AU - Lamyaa Mehdi Assad AU - Ali Hussein Alwan PY - 2019 VL - 27 IS - 3 SP - 196 EP - 214 JO - Journal of University of Babylon مجلة جامعة بابل SN - 19920652 23128135 AB - This research work represents the study of the effect of using different gas pressures of argon on the tensile behavior of tungsten inert gas (TIG) welded stainless steel sheets type (304). Different ranges of gas pressures (13-15 Kgf/cm2)and welding currents (80-100 Apm) were used to determine their influenceon the tensile mechanical properties (0.2% yield stress, ultimate tensile stress and elongation) of butt welded joints.Design of experiment (DOE) ‘version 10’ was used to establish the design matrix of experiments. Response surface methodology (RSM) technique was employed to obtain mathematical models for the three properties, which were analyzed by the analysis of variance (ANOVA) to verify statistically the adequacy of the resulted models. The resultant quadratic models with a confidence level of 95% revealed thatthe increase in both gas pressure and currentindividually results in a higher increase in the yield stress and elongation,and both were proportionated inversely,while their combined effect gave the lowest values.The gas pressure had a greater impact on the ultimate tensile stress than current. After numerical optimization, the maximum values of the mechanical properties were obtained with a maximum desirability value at the optimum values of gas pressure and current. Finally, confirmation tests were conducted at the optimum values of gas pressure and current to verify the validation of the maximum values of properties, and the error wasfound less than (4%) between the experimental and predicted results.

يمثل عمل هذا البحث دراسة تأثير استخدام ضغوط مختلفة لغاز الاركون على سلوك الشد لصفائح الفولاذ المقاوم للصدأ نوع (304) الملحومة بغاز التنجستن الخامل. استخدمت مديات مختلفة من ضغوط الغاز (13-15)كغم قوة/سم2وتيارات لحام (80-100) أمبيرلأيجاد تاثيراتها على خواص الشد الميكانيكية (0.2% اجهاد الخضوع، اجهاد الشد الاقصى والاستطالة) لوصلاتاللحام التناكبية.تم استخدام برنامج تصميم التجارب(DOE) (نسخة 10) لعمل مصفوفة التجارب. تم تطبيق منهجية الاستجابة السطحية (RSM) لأيجاد النماذج الرقمية للخواص الثلاثة والتي تم تحليلها بأستخدام تحليل التباين (ANOVA) للتحقق احصائيا" من ملائمة النماذج الناتجة. اظهرت النماذج التربيعية المستحصلة بمستوى ثقة (95%) بأن الزيادة في كل من ضغط الغاز والتيار بشكل منفصل ادت الى زيادة عالية في اجهاد الخضوع والاستطالة وكلاهما تناسب عكسيا"، بينما اعطى التأثير المشترك لهما القيم الادنى. كان لضغط الغاز تأثيرا كبيرا" على اجهاد الشد الاقصى من التيار. ER -