TY - JOUR ID - TI - Analyzing Mechanical Properties of Silica Gel Filled with Carbon Fiber into Polymeric Composite AU - Reem Alaa Mohammed AU - Aseel B. AL-Zubidi AU - MarwahSubhi Attallah PY - 2019 VL - 27 IS - 3 SP - 224 EP - 237 JO - Journal of University of Babylon مجلة جامعة بابل SN - 19920652 23128135 AB - In this study, the effect of (1%, 2%, 3%, 4% weight fraction) waste silica gel reinforced with (3% weight fraction) carbon fiber into unsaturated polyester resin was investigated on the tensile properties, impact strength and shore D hardness. These samples of polymeric composite materials were manufactured by (Hand-lay-up) method. The average particle size of the silica gel was (5.3 to 136.4 µm). The mechanical properties were analyzed using SPSS one way analysis of variance to determine which weight fraction has more influence on mechanical properties where statistical significance was set at P ≤ 0.05. Results showed that the highest mean values (164 ± 4.000 MPa), (7.367 ± .2517GPa) and (83.600 ± .2590) for tensile strength, elasticity modulus and hardness shore D respectively were recorded in sample (UP+3% C.F+4%Silica gel), while the highest mean values of elongation percentage (3.200 ± .2100), (2.700 ± .2100 ),(2.233 ± .1528) were recorded in samples (UP, UP+3% C.F, UP+3% C.F+1% silica gel) respectively, also highest mean values (10.9667±.07638) of impact strength was recorded in sample (UP+3% C.F+3% silica gel). The results of SPSS show that when (P) values less than (0.05) a significant effect of the filler material on the mechanical properties will be.

في هذه الدراسة، تم دراسة تأثير (1 ٪ ، 2 ٪ ، 3 ٪ ، 4 ٪ الكسور الوزني) السيليكا جل المقوى بألياف الكربون (3 ٪ كسر وزني) في رانتج البولي استر غير المشبع على خصائص الشد ، مقاومة الصدمة وصلادة الشور (D). تم تصنيع هذه العينات من المواد المركبة البوليمرية بطريقة (الصب اليدوية). كان متوسط حجمالجسيماتمنالسيليكاجل (5.3 إلى 136.4 ميكرون). تم تحليل الخواص الميكانيكية باستخدام SPSSتحليل التباين الاحادي لتحديد أي كسر وزني له تأثير أكبر على الخواص الميكانيكية حيث تم تعيين دلالة إحصائية عند P ≤ 0.05.أظهرت النتائج أن أعلىقيم متوسطه (164 ± 4.000 MPa) , (7.367 ± .2517GPa)و( (83.600 ±.2590 لمقاومة الشد ، معامل المرونة وشور الصلادة Dكانت مسجلة في العينة (البولي استر غير المشبع + 3% ليف كاربون + 4% سيليكا جل) ، في حين كانت أعلى قيم متوسطة لنسبة الاستطالة (3.200 ± .2100) ، (2.700 ± .2100) ، (2.233 ± .1528) كانت مسجلة في العينات (البولي استر غير المشبع، البولي استر غير المشبع + 3% ليف كاربون ، البولي استر غير المشبع + 3% ليف الكاربون + 1% سيليكا جل) على التوالي، وأيضا كانت أعلى قيم متوسطة (10.9667 ± .07638) لمقاومة الصدمةكانت مسجلة في العينة (البولي استر غير المشبع + 3% ليف الكاربون + 3% سيليكا جل).تظهر نتائج SPSS أنه عندما تكون قيم (P) أقل من (0.05) سيكون هناك تأثير كبير لمادة الحشو على الخواص الميكانيكية. ER -