TY - JOUR ID - TI - Evaluating Electrocoagulation Process for Water Treatment Efficiency Using Response Surface Methodology تقييم كفاءة عملية التخثير الكهربائي قي معالجة المياه باستخدام طريقة سطح النمذجة AU - Rand Shakir Mahmood رند شاكر محمود AU - Nawar O.A.Al-Musawi نوار عمران علي الموسوي PY - 2020 VL - 26 IS - 9 SP - 11 EP - 23 JO - Journal of Engineering مجلة الهندسة SN - 17264073 25203339 AB - The electrocoagulation process became one of the most important technologies used for water treatment processes in the last few years. It’s the preferred method to remove suspended solids and heavy metals from water for treating drinking water and wastewater from textile, diary, and electroplating factories. This research aims to study the effect of using the electrocoagulation process with aluminum electrodes on the removal efficiency of suspended solids and turbidity presented in raw water and optimizing by the response surface methodology (RSM). The most important variables studied in this research included electrode spacing, the applied voltage, and the operating time of the electrocoagulation process. The samples were taken from the Al Qadisiyiah water treatment plant. The treatment set up was in a batch mode; two parallel plates of aluminum were used as electrodes. Experimental results showed that the maximum removal efficiency of 96% for turbidity and 97% for TSS were obtained at operating time 60 minutes, voltage 30 V, and electrode spacing 1.7cm. Two models for predicting removal efficiency obtained, the first model was for turbidity with a correction factor of 94.7%, and the second one was for the TSS with a correction factor of 94.85%.

أصبحت عملية التخثير الكهربائي واحدة من أهم التقنيات المستخدمة لعمليات معالجة المياه في السنوات القليلة الماضية. إنها الطريقة المفضلة لإزالة المواد الصلبة العالقة والمعادن الثقيلة من المياه لمعالجة مياه الشرب ومياه الصرف الصحي من مصانع النسيج ، والألبسة ، والطلاء الكهربائي. الهدف من هذا البحث هو دراسة تأثير استخدام عملية التخثير الكهربائي مع أقطاب الالمنيوم على كفاءة إزالة المواد الصلبة العالقة والكدرة في المياه الخام باستخدام طريقة منهجية سطح الاستجابة.اهم المتغيرات التي تمت دراستها في هذا البحث هو المسافة بين الاقطاب ، والجهد المطبق ، ووقت التشغيل لعملية التخثير الكهربائي.تم اخذ العينات من محطة معالجة مياه القادسية لهذه الدراسة. تمت عملية المعالجة بطريقة ال (batch mode) ، باستخدم لوحان متوازيان من الألومنيوم يستخدمان كأقطاب كهربائية. أظهرت النتائج المختبرية أن أقصى كفاءة إزالة تبلغ 96٪ للكدرة و 97٪ لـ للمواد الصلبة العالقة و التي تم الحصول عليها في وقت التشغيل 60 دقيقة ، والجهد 30 فولت ، المسافة بين الاقطاب 1.7 سم. تم الحصول على نموذجين للتنبؤ بكفاءة الإزالة ، وكان النموذج الأول للكدرة بعامل تصحيح 94.7٪ والثاني لـ للمواد الصلبة العالقة بعامل تصحيح 94.85٪. ER -