TY - JOUR ID - TI - Physical Thermal Effect Test for Treatment of Polystyrene Plastic Waste اختبار فاعلية المؤثر الفيزيائي الحراري في معالجة النفايات البلاستيكية المصنعة من مادة البولي ستايرين AU - Ali M. Ahmed علي محمد احمد AU - Ahmed N. Mahmood احمد نوري محمود AU - Rasheed M. Yousuf رشيد محمود يوسف PY - 2020 VL - 29 IS - 4 A SP - 32 EP - 43 JO - Rafidain journal of science مجلة علوم الرافدين SN - 16089391 AB - Two groups of plastic waste manufactured from polystyrene (PS) were used to manufacture samples, the first group of polystyrene (Ps) is not subject to recycling, while the second group was made of polystyrene (Ps), which was subject to a recycling process using the sulfonation method and by (19.3%). The first group was called the saturated polystyrene group, while the second group was called unsaturated polystyrene, Manufactured samples underwent surface hardness and bending durability checks before and after exposure to a thermophysical effect at temperatures ((T = 60, 80 and 100 C0)). The results indicated that the polystyrene cannot maintain its surface hardness in case it is exposed to a thermophysical effect. The amount of decrease in the value of the surface hardness takes the exponential form instead of the linear shape, the extent that the value of the surface hardness is fixed with the increase in the time period of exposure to the thermophysical effect. Even if the change in the effect value was relatively few. And that there is a critical time period in which the bending resistance of the polystyrene material reaches the maximum value, after which the ability of the material to resist the bending decreases with an increase in the time period of exposure to the thermophysical effect. The effects associated with the bending process (tension, compression, shear) collapse after exposure to the thermophysical effect during a critical time period due to the loss of the continuity property in the body of the polystyrene, and finally the material loses its ability to resist the bending, and this characteristic depends on the quality of the polystyrene .

مجموعتان من النفايات البلاستيكية المصنعة من مادة البولي ستايرين (PS) تم استخدامهما لتصنيع نماذج، المجموعة الاولى من مادة البولي ستايرين (Ps) غير الخاضع لعملية اعادة تدوير اما المجموعة الثانية صنعت من مادة البولي ستارين (Ps) والتي خضعت لعملية اعادة تدوير باستخدام طريقة السلفنه وبنسبة (19.3 %). سميت المجموعة الاولى بمجموعة البولي ستايرين المشبع اما الثانية فقد سميت بالبولي ستايرين غير المشبع، خضعت النماذج المصنعة لفحوصات الصلادة السطحية وفحوصات متانة الانحناء قبل وبعد تعريضها الى مؤثر فيزيائي حراري وبدرجات حرارية (T = 60, 80 and 100) C0)). ولقد بينت النتائج ان لا قدرة للبولي ستايرين للحفاظ على صلادته السطحية في حال تعرضه لمؤثر فيزيائي حراري. وان مقدار التناقص في قيمة الصلادة السطحية يأخذ الشكل الاسي بدلا من الشكل الخطي ليصل الى حد تثبت فيه قيمة الصلادة السطحية مع زيادة الفترة الزمنية للتعرض للمؤثر الفيزيائي الحراري. كما ان مقدار التناقص في الصلادة السطحية لمادة البولي ستايرين يعتمد على طبيعة المؤثر الفيزيائي الحراري، حتى إذا كان التغير في قيمة المؤثر قليلاً نسبيا". وان هناك فترة زمنية حرجة تصل فيها مقاومة الانحناء لمادة البولي ستايرين الى القيمة العظمى، حيث تتناقص بعدها قدرة المادة على مقاومة الانحناء مع زيادة الفترة الزمنية للتعرض للمؤثر الفيزيائي الحراري. كما ان حالة التوازن بين المؤثرات المصاحبة لعملية الانحناء (الشد، الانضغاط، القص) تنهار بعد التعرض الى المؤثر الفيزيائي الحراري خلال فترة زمنية حرجة. بسبب فقدان خاصية الاستمرارية في بدن مادة البولي ستايرين، واخيرا تفقد المادة قدرتها على مقاومة الانحناء، وان هذه الصفة تعتمد على نوعية مادة البولي ستايرين. ER -