TY - JOUR ID - TI - Influences of Mg Addition on the Mechanical Properties of Cu-Al-Ni Shape Memory Alloys تأثير اضافة المغنيسيوم على الخصائص الميكانيكية للسبيكة الذاكرة للشكل( Ni-Al-Cu )المحضرة بتقانة تكنولوجيا المساحيق AU - Raed N. Razooqi AU - Omar J. Abdulkareem PY - 2020 VL - 27 IS - 3 SP - 82 EP - 93 JO - Tikrit Journal of Engineering Sciences مجلة تكريت للعلوم الهندسية SN - 1813162X 23127589 AB - Shape Memory Alloys (SMAs) are a unique class of material that possessesunconventional properties such as the shape's memory effect, the high flexibilityassociated with damping capabilities, high wear resistance and fatigue. Given itsuse in a variety of technological applications, its studies have attracted increasedinterest in the community of scientists and researchers during the past decades.The shape memory alloy (Cu 83%-Al 13%-Ni 4%) and the other alloy with addingthe alloying elements (Mg) with content of (0.25, 0.5, 0.75, 1.0, 1.25) % as avolumetric ratio which was taken from the copper percentage were prepared bypowder metallurgy, The powders were mixed using (V-type) powders mixer withmixing speed and time (20 rpm), (16 min) respectively then the samples werepressed by a two-way press (floating die) and pressing pressure (500 MPa) then thegreen samples where sintered by using vacuum furnace with using Argon gasmedium at a temperature (900°C) for one hour and left in the oven to cool down toroom temperature.The results showed that both bulk density and apparent density compared to thebase alloy increase by increasing the volumetric fraction of Mg by the ratios(5.49)% compared to the bulk density of the base alloy and by the ratios (1.51)%compared to the apparent density of the base alloy. accompanied by a decrease inthe real and apparent porosity and water absorption, The results of the mechanicaltests showed an increase in the hardness and diametrical compressive strength withthe increase of volumetric fraction of (Mg) compared to the base alloyaccompanied by a decrease in the rate of wear, The (XRD) test observes thecomposing phases (α(Cu4Al), β(Cu3Al), γ(Cu9Al44)) in addition to determiningthe transformation temperature from the Martensite to the Austenite by examiningthe (DSC) it was found that the Austenite initiation and finish (As), (Af) increasedby adding the alloying elements (Mg).

تمثل السبائك الذاكرة للشكل SMAs (Alloys Memory Shape )فئة فريدة من المواد التي تمتلك خصائص غير تقليدية مثل التأثير الذاكر للشكل، المرونةالفائقة المرتبطة بقدرات التخميد ومقاومـة التآكـل والكـالل العاليتيـن. وبالنظـر الستخدامهـا في مجموعـة متنوعـة من التطبيقـات التكنولوجية، فقد لفتت دراساتهااالهتمام المتزايد في مجتمع العلماء والباحثين خالل العقود السابقة. وتم تحضير السبائك بتقانة ميتالورجيا المساحيق وبنسب )%83 Ni 4 -%Al 13 -%Cu )للسبيكة االساس وقد تم اضافة العنصر Mg بالنسب % )25.1 ,0.1 ,75.0 ,5.0 ,25.0 ، )تـم خلط المساحيق باستخدام جهاز خلط المساحيق نوع )V )بسرعة وزمن خلط )20 min 16)، (m.p.r )على التوالي وكبست العينات بوساطة قالب كبس )عائم( باتجاهين وبضغط كبس )500 MPa ،)تم تلبيد العيناتالخضراء باستخدام فرن كهربائي مفرغ من الهواء وبوسط من غاز االرغون بدرجة حرارة )900°C )لمدة ساعة واحدة وتركت العينات بالفرن لت برد الىدرجة حرارة الغرفة. وأظهرت النتائج زيادة كل من الكثافة الحجمية والكثافة الظاهرية بزيادة الكسر الحجمي للمغنيسيوم بالنسبة )49.5 %)عند محتوى)25.1 )%مقارنة بالكثافة الحجمية للسبيكة االساس و بالنسبة )51.1 %)عند النسبة ذاتها مقارنة بالكثافة الظاهرية للسبيكة االساس رافقهما انخفاض فيالمسامية الحقيقية والظاهرية وقابلية امتصاص الماء، كما أظهرت نتائج الفحوصات الميكانيكية زيادة في الصالدة ومقاومة االنضغاطية القطرية مع زيادة الكسرالحجمي للعنصر )Mg )مقارنة بالسبيكة االساس، توافق ذلك مع انخفاض في معدل البلى. ومن خالل فحص حيود االشعة السينية تم التعرف على االطوارالمتكونة وهي ) Cu9Al44 (γ)،Cu3Al(β)، Cu4Al(α ))عالوة على تحديد درجات حرارة التحول من المارتنسايت الى االوستنايت من خالل فحص مسعرالمسح التبياني اذ ازدادت كل من درجة حرارة بدء ونهاية تحول االوستنايت )As )و )Af )بنسب مختلفة عند اضافة المغنيسيوم. ER -