@Article{, title={Evaluation The Effect of different Cooling Cycles on The Hardness Surface of the Conventional Feldspathic Zirconia تقييم تأثير دورات التبريد المختلفة على سطح صلابة الزركونيا التقليدية الفلسية}, author={Abdul Kareem J. Al-Azzawi عبد الكريم جاسم العزاوي and Lateef Essa Alwan لطيف عيسى علوان and Shahad Hazim Ali شهد حازم علي حسين}, journal={Journal of Techniques مجلة التقني}, volume={3}, number={3}, pages={E96-E101}, year={2021}, abstract={Cooling rate is the main fact in success and life span of all ceramic restoration through its effect on mechanical properties and producing a residual tensile stress, crack propagation and failure restorations. The goalsof this study was to assess the impact of diverse cooling cycles (slowcooling – fast cooling) on the surface hardness of the Zirconia (VM9). A total of 30 conventional Y-TZP Zirconia (Vita VM9) disks were fabricated according manufacturers recommendation. The samples were partition into three categories depending on the cooling system. Each group consisted of Ten specimens in diameter (2mm×10mm). Control group: samples are unescorted by any change. Fast cooling group:these specimens were fast cooled after second firing (925C0 -600C0) with opening Oven muffle 25% with holding time for 5 minute and remove from the furnace to cool at room temperature. Slow cooling group: specimens were slow cooled after second firing (925C0 -400C0) with opening Oven muffle 25% with holding time for 5 minute and remove from the furnace to cool at room temperature. Each specimen was subjected to hardness test in load 9.8N at 15s using Digital microvickers Hardness tester, Scanning electron microscope. The statistical analysis revealed that, the highest vickers hardness mean value was for the control group (690.57 ± 69.9563)and for seconed group (618.12± 53.6164) and for third group (631.75±65.3858), The facts were statistically examined by applying ANOVA test (P- value) testes which revealed significant differences(p=0.038) (p<0.05) among groups. Conclusion: The impact of cooling cycle on the hardness surface measurements of the Zirconia (Vita VM9) between the three groups was significant. The slow cooling show a higher values of (VH) Hardness and recommended for Zirconia than the fast cooling.

معدل التبريد هو الحقيقة الرئيسية في النجاح والعمر الافتراضي لجميع عمليات ترميم السيراميك من خلال تأثيره على الخواص الميكانيكية وإنتاج إجهاد الشد المتبقي وانتشار الشقوق وفشل العينات. كانت أهداف هذه الدراسة هي تقييم تأثير دورات التبريد المتنوعة (التبريد البطيء - التبريد السريع) على صلابة سطح الزركونيا (VM9). تم تصنيع ما مجموعه 30 قرصًا تقليديًا من نوع Y-TZP Zirconia (Vita VM9) وفقًا لتوصية الشركات المصنعة. تم تقسيم العينات إلى ثلاث فئات حسب نظام التبريد. تتكون كل مجموعة من عشر عينات بقطر (2 مم × 10 مم). المجموعة الضابطة: العينات غير مصحوبة بأي تغيير. مجموعة التبريد السريع: تم تبريد هذه العينات سريعًا بعد الحرق الثاني (C0925-600 C0) مع فتح الفرن بنسبة 25 ٪ مع وقت احتجاز لمدة 5 دقائق وإخراجها من الفرن لتبرد في درجة حرارة الغرفة. مجموعة التبريد البطيء: تم تبريد العينات ببطء بعد الحرق الثاني (C0925-400 C0) مع فتح الفرن بنسبة 25 ٪ مع وقت احتجاز لمدة 5 دقائق وإخراجها من الفرن لتبرد في درجة حرارة الغرفة. تم إخضاع كل عينة لاختبار الصلابة في الحمل 9.8N عند 15 ثانية باستخدام جهاز اختبار الصلابة الرقمي ، ميكروسكوب المسح الإلكتروني. أظهر التحليل الإحصائي أن أعلى قيمة لمتوسط صلابة فيكرز كانت للمجموعة الضابطة (690.57 ± 69.9563) وللمجموعة الثانية (618.12 ± 53.6164) وللمجموعة الثالثة (631.75 ± 65.3858) تم فحص الحقائق إحصائياً عن طريق تطبيق اختبار ANOVA (P- value) اظهرت فروق معنوية (p = 0.038) (p <0.05) بين المجموعات. الخلاصة: تأثير دورة التبريد على صلابة سطح الزركونيا (Vita VM9) بين المجموعات الثلاث كان معنويا. يُظهر التبريد البطيء قيمًا أعلى للصلابة (VH) ويوصى بها لزركونيا من التبريد السريع.} }