TY - JOUR ID - TI - Simulation of Temperature Distribution in TIG Spot Welds of(Al-Mg) Alloy Using Finite Element Method محاكاة التوزيع الحراري لوصلات اللحام النقطي (TIG Spot)لسبيكةالمنيوم- مغنيسيوم باستعمال طريقة العناصر المحددة AU - Ahlam Abid Ameer Alkhafajy احلام عبد الامير AU - Abdul Hussain G. Al-Maliky عبد الحسين غانم المالكي AU - Muna K Abbas منى خضير عباس PY - 2008 VL - 4 IS - 2 SP - 83 EP - 97 JO - Al-Khwarizmi Engineering Journal مجلة الخوارزمي الهندسية SN - 18181171 23120789 AB - This research concern to analyse and simulate the temperature distribution in the spot welding joints using tungsten arc welding shielded with inert gas (TIG Spot) for the aluminum-magnesium alloy type (5052-O). The effect of and the quantity of the heat input that enter the weld zone has been investigated welding current, welding time and arc length on temperature distribution. The finite element method (by utilizing programme ANSYS 5.4) is presented the temperature distribution in a circular weld pool and the weld pool penetration (depth of welding) through the top sheet ,across the interface into the lower sheet forming a weld spot. A three dimensional (3-D) model has been constructed to study the temperature distribution and the depth or penetration of the weld spot. The results showed that the weld zone and heat affected zone (HAZ) suffer from high temperature variation caused by severe thermal cycle. The temperature reaches the highest value of the melt metal at the weld spot 698°C at weld current 130 Amp, weld time 6 sec and arc length 1.6 mm, then drops further away from the weld spot in the direction the base metal. Figuers were plotted to explain the results and to show the temperature distribution and its value in the weld spot and heat effected zone.

يتناول هذا البحث تحليل ومحاكاة التوزيع الحراري لوصلات اللحام النقطي بطريقة القوس الكهربائي بقطب التنكستن المحمي بالغاز الخامل ((TIG Spot لسبيكة الألمنيوم- مغنيسيوم نوع (5052-O) من خلال استخدام طريقة العناصر المحددة(Finite Element Method) باستخدام برنامج (ANSYS¬-5.4) ومعرفة تأثير متغيرات اللحام من تيار اللحام, زمن اللحام وطول القوس في التوزيع الحراري وكمية الحرارة الداخلة في منطقة اللحام. تم بناء أنموذج العناصر المحددة ثلاثي (3-D) الأبعاد لمعرفة التوزيع الحراري في بركة اللحام الدائرية وملاحظة مقدار تغلغل (عمق اللحام) المعدن المنصهر داخل منطقة اللحام من خلال الصفيحة العليا عبر السطح الفاصل الى الصفيحة السفلى مكونة نقطة اللحام (spot Weld). ورسمت العلاقات التي تبين توزيع درجات الحرارة وقيمها في مناطق اللحام المختلفة (منطقة اللحام والمنطقة المتأثرة بالحرارةHAZ))). أوضحت النتائج إلى أن منطقة اللحام والمنطقة المتأثرة بالحرارة تتعرض إلى انحدار وتباين كبيرين في درجات الحرارة بسبب الدورة الحرارية الشديدة نتيجة لعمليتي التسخين والتبريد, حيث وصلت أعلى قيمة لدرجة الحرارة للمعدن المنصهر في نقطة اللحام إلى ( (698°C تقريبا عند زمن لحام (6sec) وتيار لحام (130A) وطول قوس (1.6mm) ثم انخفضت باتجاه المعدن الأساس البعيد عن منطقة اللحام. ER -