TY - JOUR ID - TI - Study of the Mechanical and Metallurgical Properties of Dissimilar Welds AU - Sami A. Nawi AU - Kasim A. Khalaf AU - Muna K. Abbas PY - 2007 VL - 13 IS - 1 SP - 1283 EP - 1294 JO - Journal of Engineering مجلة الهندسة SN - 17264073 25203339 AB - In this research dissimilar welds were made of low carbon steel (A516) and austenitic stainless steel (316L) by shielded metal arc welding (SMAW) and with different electrodes (E7018) , (E6013) , (E309L) and (E308L). The sheet thickness (6 mm), welding current (120 A), voltage (78V), polarity (DCRP) and electrode diameter (3.25 mm) were remained constant. Many tests were carried out, mechanical tests included tensile test, bending and microhardness also made , and metallurgical inspections included microstructure, delta- ferrite phase and x- ray diffraction analysis. It was found from tensile and bending tests results that the electrode (E309L) was the most convenient for dissimilar welds of base metal (C.St. A516) and (St. St. 316L). Hardness tests showed that the highest hardness value appears in (HAZ) and there are two peaks of maximum hardness, each peak value in each (HAZ) for both dissimilar metals, the peak values are not equal and the higher value appears in the zone, where the electrode differ from the base metal, i. e. when the electrode is used (E6013) the higher value appeared in the (HAZ) which is near the stainless steel (316L), and when the electrode (E309L) is used, the higher value appeared in (HAZ) near the low carbon steel (A516) .The tests demonstrated that the delta ferrite phase was about 3-10% near stainless steel and for all used electrodes.

تناول البحث انتاج وصلات لملحومات غير متشابهة من الفولاذ منخفض الكاربون (A516) مع الفولاذ مقاوم الصدأ الاوستنايتي (316L) بطريقة لحام القوس الكهربائي المعدني المغلف بالصهيرة (SMAW) باختيار اقطاب لحام مختلفة هي (E308 L, E309L, E6013, E7018) مع ثبات سمك الصحفيحة (6 mm) وتيار اللحام (120 Amp) والفولتية (78 volt) والقطبية (DCRP) وقطر قطب اللحام (3.25mm) .تم اجراء فحوصات ميتالورجية مختلفة شملت البنية المجهرية وفحص طور دلتا فبرايت والفحص بحيود الاشعة السينية وكذلك اجريت الاختبارات الميكانيكية ومنها اختبار الشد والحني والصلادة الدقيقة . أظهرت نتائج أختبارات الشد والحني ان القطب (E309L) هو الاكثر ملائمة في لحام الوصلات للملحومات غير المتشابهة من حيث المعدن الاساس (فولاذ منخفض الكاربون (A516) مع فولاذ مقاوم للصدأ (316L)) . اظهرت نتائج الصلادة ان أعلى صلادة هي في المنطقة المتأثرة بالحرارة (HAZ) وقد وصلت الصلادة الى قيم أعلى من منطقة اللحام (W.M) وهذا يعني ظهور قمتين للصلادة العظمى (قمة في كل منطقة HAZ) لكلا المعدنين غير المتشابهين وهاتين القمتين غير متساويتين وتكون الصلادة أعلى في الجانب الذي يكون فيه القطب مختلفا عن نوعية المعدن الاساس أي انه عند اللحام بقطب (E6013) اظهرت القمة العليا في (HAZ) القريب من الفولاذ مقاوم للصدأ (316 L) ، أما عند اللحام بقطب (E309 L) ظهرت القمة العليا في منطقة (HAZ) القريب من الفولاذ منخفض الكاربون في حالة الملحومات غير المتشابهة . أوضحت نتائج الفحص لطور الدلتا فيرايت ان قيمة هذا الطور تتراوح من (10-3) % من جانب الفولاذ مقاوم الصدأ ولجميع الاقطاب المستعملة . ER -