@Article{, title={PREPARATION OF CERAMIC MATERIAL (CORDIERITE) USING LOCAL ORES تحضير مادة سيراميكية (كورديرايت) باستخدام خامات محلية}, author={Zeinab K. Nassrullah زينب كريم نصرالله and Ibtisam G. Essa ابتسام غازي عيسى}, journal={Iraqi Bulletin of Geology and Mining مجلة الجيولوجيا والتعدين العراقية}, volume={18}, number={1}, pages={47-57}, year={2022}, abstract={The research aims to prepare cordierite by using sources of alumina, silica, and magnesia from local and available raw materials (kaolin and dunite rocks). Cordierite ceramic was prepared by different mixtures of raw materials, different preparation methods (molding and hydraulic pressing) were used to form the starting materials, also magnetic separation was used to purify dunite from iron. Sintering the prepared samples at different temperatures (1200, 1250, 1300, and 1350 °C) for 2 hours. The prepared sintered samples were characterized by chemical analysis, X-ray diffraction, porosity, and bulk density. The proportions of oxides affect the preparation of cordierite also sintering temperature is a very important factor. For samples prepared by molding at temperatures (1200 – 1250) °C, different minerals appeared with cordierite (mullite, cristobalite, and corundum) by increasing the sintering temperature to 1300 – 1350 °C the cordierite peaks increased. Samples prepared by using dunite 30 wt.% and 40 wt.% cordierite was the only mineral that appeared. The preferred dunite rocks content was 30 wt.% because increasing the percentage of dunite in the mixture at 1350 °C leads to deforming of the sample. The chemical analysis of the sample prepared by 30 wt.% dunite and 70 wt.% kaolin is close to the chemical composition of cordierite. Different mixtures were pressed and sintered at temperatures 1250 °C and 1300 °C. The only mineral that appeared at 1250 °C was cordierite but with lower intensity compared to the sample sintered at 1300 °C. At 1300 °C, cordierite peaks are accompanied by small peaks of clinoenstitate. Samples prepared with 20 wt.% and 30 wt.% dunite sintered at 1300 °C had high peaks intensities of cordierite, the sample prepared with 20% dunite is closer to the chemical composition of cordierite. Magnetic separation was used to reduce iron in dunite to 1.21%, and different quantities of dunite were used (20 wt.%, 30 wt.%, and 40 wt.%) sintered at 1350 °C. In mixtures containing 30 and 40% dunite, cordierite was the only mineral. By using magnesium oxide instead of dunite rock in the mixture and sintered at different temperatures of 1200 – 1350 °C, cordierite appeared with mullite and cristobalite in all samples.

يهدف هذا البحث الى تحضير الكورديرايت من اكاسيد المغنيسيوم والالمنيوم والسيلكا من مصادر محلية متوفرة هي الكاؤولين وصخور الدونايت. تم تحضير عدة خلطات لتجارب تحضير المواد السيراميكية الحاوية على الكورديرايت. تم استخدام طرق مختلفة لتشكيل نماذج الخلطات المحضرة (الصب و الكبس). ايضا تم استخدام جهاز الفصل المغناطيسي لتقليل نسبة اوكسيد الحديد في الدونايت قبل استخدامه في تحضير الخلطات. النماذج التي تم تحضيرها تم معاملتها بدرجات حرارية مختلفة 1200، 1250، 1300 و 1350 ◦م لمدة ساعتين. تم فحص النماذج بالاشعة السينية الحائدة والتحليل الكيميائي وفحص المسامية وفحص الكثافة الكلية. نسبة المواد الداخلة للخلطة لها تاثير على تحضير الكورديرايت ودرجة الحرارة المستخدمة في المعاملة عامل مهم في التحضير. بالنسبة للنماذج التي تم تحضيرها بطريقة الصب وبدرجة حرارة 1200 و 1250 ◦م عدة معادن ظهـــرت مصاحبة للكورديرايت (مولايت، كريستوبلايـت، وكوروندوم)، بزيادة درجة الحرارة الى 1300◦ م ارتفعت شدة منحنيات الكورديرايت في النماذج، بدرجة حرارة 1350 ◦م ونسبة دونايت في النموذج 30% و 40% ظهر الكورديرايت بمفرده، في النموذج الحاوي على 40% دونايت بدء ظهور انصهار طفيف، لذلك اعتبرت النسبة 30% دونايت هي الأفضل ومن ناحية التركيب الكيميائي كانت النسب قريبة للنسب النظرية مع انخفاض في نسبة اوكسيد السيليكون. استخدم المكبس الهايدروليكي لتحضيرعدة نماذج وتم معاملتها بدرجات حرارة 1250و 1300 ◦م. النماذج الناتجة بدرجة حرارة 1250 ◦م تكونت من الكورديرايت فقط ولكن بشدة منخفضة، وبدرجة حرارة 1300 ◦م ارتفعت قمم الكورديرايت وخصوصا مع 20 و 30% دونايت ولكن ظهرت أطوار أخرى. لدراسة تاثير اوكسيد الحديد تم استخدام جهاز الفصل المغناطيسي الجاف لتقليل نسبته في الدونايت الى 1,21% قبل استخدامه في تحضير الخلطات وبنسب 30، 20، 40%، ومعاملته بدرجة حرارة 1350 ◦م. النماذج المكونة من 30 و40% دونايت ظهر فيها الكورديرايت بمفرده. استخدم اوكسيد المغنيسيوم في تحضير بعض الخلطات بدلا من الدونايت، وتمت المعاملة الحرارية بدرجات حرارة 1200، 1250، 1300، 1350 ◦م، ظهر الكورديرايت مصاحبا للمولايت والكريستوبلايت في جميع النماذج.} }