TY - JOUR ID - TI - Evaluation of Welding Sequences for Patching in Steel Gears AU - Selah S. Abdul Kareem AU - Nabeel K. Abid Al Sahib PY - 2005 VL - 11 IS - 1 SP - 1 EP - 19 JO - Journal of Engineering مجلة الهندسة SN - 17264073 25203339 AB - The present work deals with an experimental investigation of the effect of surfacing parameters on the final quality of large gear surfacing. This gear forms a vital part of the drive train of cement furnace at the Iraqi Cement Company. The gear is made of DIN CK 45 steel with an analyzed carbon content of 0.429 % and core hardness 185 HV. The gear is considered large, with dimensions of 490 mm in diameter, 250 mm width and 27 mm module, its weight is 350 Kg. The aim of the present work is to study the possibility of repairing this type of gear using SMAW process.The gear surface is cleaned by sand blasting, followed by dye penetrate testing for crack detection. DIN E1-UM350 hardfacing electrode is selected to hardface the gear. This electrode has a nominal composition (0.08 % C, 3.3 % Cr, 1% Mn) and a minimum hardness 350 HV. The gear teeth are surfaced with one, two, and three layers with and without preheating. The preheating temperature is 200 Cْ, which is, selected according to carbon equivalent of the DIN CK 45 base metal. Cracks were observed in the weld metals when surfacing with three layers of E1-UM350 electrode. So, E 8018-B2, and E9018-D1 are selected to butter the gear surface with one layer, followed by two layers of E1-um350 electrode. These low hydrogen electrode are selected based on their mechanical properties compared with DIN CK 45 base metal and low hydrogen content which eliminate hydrogen induced cold cracking. Preheating the gear surface gives good hardness distribution across the weld, HAZ, and base metals due to reducing the cooling rates and prevents hard structure to form at the interface region.A set of destructive and non destructive tests are carried out. Including, tensile wear, impact, chemical analysis, metallographic, micro hardness, macro etchant, and dye penetrate tests. Both of wear and impact resistance of all specimens is greater than the base metal. All weld deposits of E1-UM350 hardfacing electrode gives martensitic structures with different hardness depending on the cooling rates and number of layers. Using of low hydrogen electrodes (E 8018-B2 and E 9018-D1) as buttering layers, solve the cracking problem of weld deposits when surfacing with three layers of E1-UM350 electrodes.

في هذا البحث تم دراسة امكانية اصلاح التروس باستخدام تقنية اللحام اليدوي . الترس المستخدم في هذا البحث هو الفولاذ متوسط الكربون (DIN CK 45) تم جلبه من شركة السمنت العراقية . يشكل هذا الترس جزء حيوي من منظومة التدوير لافران تجفيف السمنت . نسبة الكربون لهذا الفولاذ 0.429% وله صلادة قلب (HV 185) . يعتبر هذا الترس كبيرا نسبيا حيث يزن 350 كغم , قطره الخارجي 490 ملم , عرضه 250 ملم , وتضمينه 27 ملم.تم تنظيف جميع اسنان الترس بواسطة العصف الرملي ومن ثم فحص الترس بالسوائل النافذة للتأكد من عدم وجود شقوق. أسطح الاسنان هيئت بواسطة تجليخها يدويا. كسيت اسنان الترس بطبقة , طبقتين , وثلاث طبقات من سلك (E1-UM350) باستخدام تسخين مسبق وبدونه . التركيب الكيمياوي لهذا السلك ( 0.08% ,C, 3.3 %Cr, 1%Mn ) وصلادته الدنيا (350 Hv ) والتي تمثل الصلادة القصوى لسطح اسنان الترس , وعلى هذا الاساس تم اختيار هذا السلك لاجراء الاكساء . تم اختيار درجة حرارة التسخين المسبق (200° C) لسطح الاسنان اعتمادا على قيمة الكربون المكافئ.لوحظت تشققات في منطقة اللحام عند الاكساء بثلاث طبقات من سلك (E1- UM350) وعليه اختيرت اسلاك لحام واطئة المحتوى من الهيدروجين (E8018-B2) و (E 9018-D1 ) لتزبيد سطح الاسنان ثم تتبع بطبقتين من سلك (E1-UM350) . اختيرت هذه الاسلاك لغرض التزبيد لخواصها الميكانيكية الجيدة اذا ما قورنت بالمعدن الاصلي وكذلك محتواها الواطئ من الهيدروجين وبالتالي تضمن عدم ظهور شقوق من منطقة اللحام او المنطقة المتأثرة بالحرارة.اجريت مجموعة من الفحوصات الاتلافية وغير الاتلافية لغرض تقيم مناطق اللحام ميكانيكيا وميتالورجيا. من هذه الفحوصات , فحص الشد, الصلادة المايكروية , مقاومة البليان , مقاومة الصدمة , فحص السوائل النافذة, التحليل الكيمياوي , الفحص المجهري , والاظهار الماكروي.ان اجراء التسخين المسبق لسطح الأسنان اعطى توزيع جيد للصلادة خلال مناطق اللحام , المنطقة المتأثرة بالحرارة , والمعدن الأصلي من خلال خفض معدلات التبريد ومنع ظهور أطوار صلدة في المنطقة المتأثرة بالحرارة . مقاومة البليان والصدمة لمناطق اللحام كانت اكبر من المعدن الاصلي . اظهر الفحص المجهري لمناطق اللحام لسلك (E1-UM350) بنية المارتنسايت بصلادات مختلفة اعتمادا على معدل التبريد وعدد الطبقات . ان استخدام اسلاك لحام وطئة المحتوى من الهيدروجين كطبقة تزبيد, عالج مشكلة التشقق في منطقة اللحام. ER -