TY - JOUR ID - TI - Study of Mechanical Characteristics for Polymer Composite Reinforced by Particles of (Al2O3) or (Al) دراسة الخصائص الميكانيكيـة لمـادة مركبة ذات أساس بوليمري مقواة (Al2O3) أو (Al) بدقائق من AU - Saad M. elIa سعد ميخائيل إيليا AU - Jawad Kadhim Uleiwi جواد كاظم عليوي AU - . Ali Hussein Ataiwi علي حسين عتيوي PY - 2007 VL - 3 IS - 3 SP - 17 EP - 25 JO - Al-Khwarizmi Engineering Journal مجلة الخوارزمي الهندسية SN - 18181171 23120789 AB - A particulate polymer composite material was prepared by reinforcing with the Aluminum Oxide (Al2O3) or Aluminum (Al) metallic particles with a particle size of (30) µm to an unsaturated Polyester Resin with a weight fraction of (5%, 10%, 15%, 20%). Tensile test results showed the maximum value of elastic modulus reached (2400MPa.) in the case of reinforcing with (Al) particles with weight fraction (20%) and (1500 MPa.) in the case of reinforcing with (Al2O3) particles of the same weight fraction. When the impact and the flexural strength tests were done, the results showed that flexural strength (F.S), maximum shear stress (τmax), impact strength (Gc) and fracture toughness (Kc) were increased with the increase of weight fraction, where the results of the samples of (Al) particles were higher than that of (Al2O3) particles reinforced at a weight fraction of (20%) at ratios of (45.43%, 45.45%, 25%, 41%) respectively. While the hardness of the samples reinforced with (Al2O3) particles was higher than that reinforced with (Al) particles with a ratio of (2.82%) at a weight fraction of (20%).

تم تحضير مادة مركبة بوليمرية مكونة من راتنج البولي استـر غيـر المشبــع المقوى بدقائق من أوكسيـد الألمنيـوم (Al2O3) أو دقائــق معدنية مـن الألمنيوم (Al) وبحجم دقائق(30 µm) وبكسـور وزنـيه بنسب (20%, 15%, 10%, 5%). أظهرت نتائج اختبار الشد بأن أعلى قيمة لمعامل المرونة بلغت (2400 MPa.) عند التقوية بدقائق (Al) وبلغت (1500 MPa.) عند التقوية بدقائق (Al2O3) عند كسر وزني (20 %).أما عند أجراء اختبارات مقاومة الانحناء والصدمة فأظهرت النتائج بأن كل من مقاومة الانحناء (F.S) وأقصى أجهاد القص max) τ) ومقاومة الصدمة (Gc) ومتانة الكسر (Kc) تزداد مع زيادة نسبة الكسر الوزني. حيث كانت نتائج العينات المقواة بدقائق (Al) أعلى من نتائـج العينات المقواة بدقائق (Al2O3) عند كسـر وزني (20 %)بنسبة (41% ,25% ,45.45% ,45.43%) على التوالي. بينما صلادة العينات المقواة بدقائق(Al2O3) كانت أعلى من صلادة العينات المقواة بدقائق (Al) بنسبة (2.82 %) عند كسر وزني (20 %). ER -