TY - JOUR ID - TI - Estimation Pore and Fracture Pressure Based on Log Data; Case Study: Mishrif Formation/Buzurgan Oilfield at Iraq تخمين الضغط المسامي وضغط التكسير اعتمادا على بيانات تخطيط الابار لمكمن المشرف حقل بزركان النفطي AU - Sameera M. Hamed-Allah سميرة محمد حمد الله AU - Ahmed K. AlHusseini أحمد كريم الحسيني PY - 2023 VL - 24 IS - 1 SP - 65 EP - 78 JO - Iraqi Journal of Chemical and Petroleum Engineering المجلة العراقية للهندسة الكيمياوية وهندسة النفط SN - 19974884 26180707 AB - Prediction of the formation of pore and fracture pressure before constructing a drilling wells program are a crucial since it helps to prevent several drilling operations issues including lost circulation, kick, pipe sticking, blowout, and other issues. IP (Interactive Petrophysics) software is used to calculate and measure pore and fracture pressure. Eaton method, Matthews and Kelly, Modified Eaton, and Barker and Wood equations are used to calculate fracture pressure, whereas only Eaton method is used to measure pore pressure. These approaches are based on log data obtained from six wells, three from the north dome; BUCN-52, BUCN-51, BUCN-43 and the other from the south dome; BUCS-49, BUCS-48, BUCS-47. Along with the overburden pressure gradient and clay volume, which were also established first, data such as gamma ray, density, resistivity, and sonic log data are also required. A key consideration in the design of certain wells is the forecasting of fracture pressure for wells drilled in the southern Iraqi oilfield of Buzurgan. The pressure abnormality is found in MA, MB21, MC1 and MC2 units by depending on pore pressures calculated from resistivity log. In these units, depths and its equivalent normal and abnormal pressure are detected for all six selected wells; BUCS-47, BUCS-48, BUCS-49, BUCN-43, BUCN-51 and BBCN-52. For MA, MB21, MC1, and MC2 units, the highest difference in pore pressure values are 1698 psi @ 3750 m (BUCN-51), 3420 psi @ 3900 m (BUCN-51), 788 psi @ 3980 m (BUCS-49), and 5705 psi @ 4020 m (BUCN-52). On other hands, MB11 and MB12 units have normal pressure trend in all studied wells. Finally, the results show that the highest pore and fracture pressure values is existed in North dome, in comparison with that obtained in south dome of Mishrif reservoir at Buzurgan oilfield.

عند تصميم برنامج الحفر للابار النفطية فإن التنبؤ بضغط مسام التكوين وضغط التكسير يكون بالغ الأهمية لأنه يساعد على منع العديد من مشاكل عمليات الحفر بما في ذلك خسارة دورة سائل الحفر، والرفسة، و التصاق الأنابيب، والانفجار، وغيرها من المشاكل الاخرى. يستخدم برنامج IP لإجراء العمليات الحسابية وقياس ضغط المسام والتكسير. تُستخدم معادلات إيتون، ماثيوز وكيلي، إيتون المعدلة، و باركر وود لحساب ضغط التكسير، بينما تستخدم طريقة إيتون لقياس ضغط المسام. تستند هذه الطرق إلى بيانات تخطيط الابار التي تم الحصول عليها من ستة آبار: ثلاثة من القبة الشمالية BUCN-52, BUCN-51, BUCN-43 وثلاثة من القبة الجنوبية BUCS-49, BUCS-48, BUCS-47. بالإضافة الى تدرج ضغط وزن الطبقات وحجم الطين اللذين تم إحتسابهما أيضًا في بداية الحسابات لذلك اعتمدت هذه الحسابات على بيانات تخطيط الابار مثل أشعة كاما والكثافة والمقاومة وبيانات السجل الصوتي. أن أحد الاعتبارات الرئيسية في تصميم بعض الآبار هو التنبؤ بضغط التكسير للآبار المحفورة في حقل بزركان النفطي بجنوب العراق. الضغوط الغير طبيعية تم حسابها لستة ابار اعتمادا على بيانات مجس المقاومة، حيث اظهرات النتائج وجود ضغوط غير طبيعية في الوحدات MA, MB21, MC1, MC2 بينما الوحدات MB11, MB12 لها ضغوط طبيعية. أخيرًا، أظهرت النتائج أن أعلى قيم ضغط المسام والتكسير موجودة في القبة الشمالية مقارنة بالقبة الجنوبية لمكمن المشرف في حقل بزركان النفطي. ER -