TY - JOUR ID - TI - Numerical and Experimental Analyses for Effect of Welding Currents on Cooling Rates in (M MAW) Process التحليلات العددية والعملية لتاثير تيارات اللحام على معدلات التبريد بطريقة لحام القوس الكهربائي اليدوي AU - Abbas Sh. Alwan AU - Jalal M. Jalil AU - Muna K. Abbass PY - 2010 VL - 28 IS - 12 SP - 2276 EP - 2293 JO - Engineering and Technology Journal مجلة الهندسة والتكنولوجيا SN - 16816900 24120758 AB - In this study, Manual Metal Arc Welding (MMAW) is carried out for lowcarbon steel (AISI 1015) with using electrode (E7018). Direct current straightpolarity (DCSP) with the joint geometry of single -V- butt joint and weld one passare used for plate of thickness 8mm. experimentally, obtained temperaturedistribution in fusion zone which is measured by insert the thermocouple in weldmetal. Cooling rates are determined for the fusion zone at different weldingcurrents (100, 120 and 140) Amp with constant welding speed at 3.2mm/s.Numerical analysis by using the Control Volume Method (CVM), applied to threedimensionalheat transfer model to determine the cooling rate in fusion zone.Cooling rates models are helping in prediction the microstructure (phases, grainsize and volume fraction) and microhardness distribution in weld metal and heataffected zone. The comparison of cooling curves between numerical andexperimental work have a good agreement, so that deviation was in range ( 6℅ -21℅) which is confirming the capability and reliability of the proposed numericalheat transfer model in manual metal arc welding. The best result for cooling rateswhen applying mathematical model is at welding current 140Amp.

AISI ) في هذه الدراسه تم لحام صفائح من الفولاذ منخفض الكربون نوع(E باستخدام قطب لحام نوع ( 7018 (MMAW) 1015 بطريقة لحام القوس الكهربائي المعدنيوبتمريرة لصفيحة (Single –V ) على شكل وصلات تناكبية مفردة (DCSP) وقطبية مباشرة8. وتم عمليا قياس درجة الحراره في منطقة الانصهار (معدن اللحام ) mm ذات سمكبوضع مزدوج حراري في (معدن اللحام) وبعد ذلك تم رسم منحنيات التبريد مع اختلاف3.2 ). اما الدراسة mm/s) 140 ) أمبير عند سرعة لحام ثابته ,120 , تيارات اللحام ( 100النظرية فقد تضمنت التحليلات العددية لايجاد معدلات التبريد باستخدام طريقة الحجم المحدودوالتي طبقت لانتقال الحرارة الثلاثي الابعاد. وقد ساهمت معدلات التبريد النظرية بشكل فعالفي التنبؤ عن البنية المجهرية ( الاطوار, الحجم الحبيبي, والكسر الحجمي ) وكذلك توزيعالصلادة الدقيقة في معدن اللحام والمنطقة المتاثرة بالحرارة. ولغرض التحقق من صحةالنتائج العددية المستحصلة من البرنامج الحاسوبي تم اجراء المقارنة مع النتائج العمليةالمستحصلة من التجارب المختبرية حيث كانت النتائج متوافقة بشكل جيد وكان مقدار التقارب 1 ) كما تم الحصول على افضل نتيجة لمعدلات التبريد عند تطبيق أ لموديل ℅ - يتراوح (℅ 6الرياضي هي عند تيار لحام ( 140 ) أمبير. ER -