TY - JOUR ID - TI - Study Of Using The Ni-Cr Alloy Post And Increasing Cement Strength(Zinc Polycarboxylate) On The Stress Distribution Of Restored Human Tooth دراسة استخدام سبيكة (النيكل - الكروم) وسمنت الزنك بولي كاربوكسيلت ذي المقاومة العالية واثرها على توزيع الاجهادات في السن البشري المعاد AU - Kadhim K. Resan كاظم كامل رسن PY - 2011 VL - 15 IS - 3 SP - 42 EP - 54 JO - Journal of Engineering and Sustainable Development (JEASD) مجلة الهندسة والتنمية المستدامة SN - 25200917 25200925 AB - The effects of stress on dental restoration and upon teeth themselves have been a topic of interest to dental researchers for the past twenty years. A model of a maxillary central incisor (front tooth) restored with titanium alloy post and another post nickel alloy in combination with different cements, are established. The stress in dentin, posts, cores and crowns have been evaluated and compared with two different post materials and two different cements. The research is performed theoretically , numerically and experimentally, A composite beam formula is derived for analysis and the stress at sections through the tooth. The numerical analysis is achieved by use of ANSYS/ver.11 software. The material of tooth is assumed to be isotropic, homogeneous and elastic. A load of 100 N is applied at an angle of 45۫ to the longitudinal axis at the palatal surface of the crown. The mechanical properties and chemical composition of nickel alloy and Zinc polycarboxylate are measured experimentally. In this study , There are three model type (I,II and III) , model I including the standards restoring tooth (Titanium post tooth ), model II including new post (Ni-Cr) alloys and third model by using the high strength cement(Zinc polycarboxylate) . The Von Mises stress value in cement layer and post core increases with the increase of the elastic modulus of post and cement but decrease the stress in dentin.

تأثير الاجهادات في السن المعاد ترميمه كان محط اهتمام الباحثين في السنوات العشرين الماضية . تم دراسة نموذج لسن القواطع الامامية العليا للانسان معاد ترميمه بعمود تيتانيوم و تبديلة بعمود مصنوع من سبيكة النيكل- الكروم و تم استخدام نوعين مختلفين من الملاطات .الاجهاد في العاج و الاعمدة و الحشوات و التاج تم دراسته و تم كذلك اجراء مقارنة بين الاجهادات في المواد القياسية و المواد المقترحة في الاعمدة و الملاط . تم انجاز البحث نظرياً و عددياً. وقد استخدمت نظرية العتبة المركبة لتحليل السن نظرياً. أما التحليل العددي فتم انجازه بواسطة برنامج العناصر المحددةANSYS/ver.11 أُفترض السن متجانس وذو خصائص مرنة. تم تسليط قوة 100نيوتن بزاوية ۫45 عن المحور الطولي للسطح الفكي(من جانب الجهة الشفية) لتاج السن. الخواص الميكانيكية و التركيب الكيمائي تم قياسه عمليا لسيكة النيكل - كروم و لمادة الملاط عالي المقاومة ( زنك بولي كاربوكسيليت) . في هذه الدراسة تم دراسة ثلاث نماذج مختلفة (I,II,III ) النموذج الاول يتضمن عمود من مادة التيتانيوم , النموذج الثاني المقترح هو باستخدام عمود من سبيكة النيكل – كروم اما النموذج الثالث فكان باستخدام ملاط عالي المقاومة من مادة ( زنك بولي كاربوكسيليت) . لوحظ ان أجهادات فون ميسز ستزداد عند العمود مع زيادة معاملات المرونة كما انها ستزداد كذلك بزيادة معامل المرونة للملاط لكنها تنخفض عند منطقة العاج . ER -