TY - JOUR ID - TI - An Investigation Behavior Into Dental Biomechanical Analysis AU - Amal Ibrahim AU - Sadiq Jafer Abbass PY - 2008 VL - 11 IS - 3 SP - 544 EP - 551 JO - Al-Nahrain Journal for Engineering Sciences مجلة النهرين للعلوم الهندسية SN - 25219154 25219162 AB - The aim of the study is to evaluate the Von Mises stress distribution of different human teeth model. Three-dimensional model of the maxillary central incisor, mandibular first molar and mandibular central incisor were constructed using Auto CAD (Auto CAD 2007) software and then imported to ANSYS software (ANSYS V.10) to get finite element model of each teeth. A loading simulating the 200N force was applied vertically and with different inclination to the crowns. Then same loading was applied vertically but the load was distributed along the incisal area for the incisors and at occlusal margin for the molar. Finally the crown was considered as porcelain material and the vertical load was distributed along each tooth and the Von Mises stresses were calculated. The results showed that the increase in the loading angle from 0°, 26° to 45° resulted in an increase in tooth Von Mises stress which means increase the probability of tooth failure. When the load distributed along wide region the ability of model to fail for the same loading will be decreased. Also when the crown consider as porcelain material there will be increasing Von Mises stress compare with the enamel crown for the same load region and load value

إنّ هدفَ الدراسـةِ هو تقييمَ توزيعَ إجهادِ Von Mises لنماذجِ مختلفة من أسنان الإنسـان وهـي القاطع المركزي في الفك الأعلى والقاطع المركزي للفك السفلي والضرس الأول للفك السفلي. أستعمل برنامج (2007 AutoCAD) لرسم النموذج ثلاثي الأبعاد لكل سن من الأسنان التي أستخدمت للدراسة ومن ثم تحويلها الى برنامج العناصر المحددة (ANSYS V.10) للحصول على نموذجِ العنصرِ المحـدد لـكُـلّ سن من الأسـنان التي أستخدمت في هذه الدراسة. تم تسليط حمل عمودي بمقدار 200 نيوتن بشكل عمودي وبزوايا مختلفة على منطقة التاج. نفس الحمل سلط بصورة عمودية ولكن وزع على طول منطقة الحافة العليـا للقواطـع والاضـراس لحالتين الاولى بأعتبـار التـاج مكون من المينا والحالة الثانية أعتبـار التاج مكون من الخـزف وتم أيجاد قيم اجهاد (VonMises).وتم استنتاج انه الزيادة في زاوية التحميل (مِنْ صفر°, 26° إلى 45°) أدت الى الزيادة في اجـهـاداتVon Mises مما يؤدي الى زيادة فشـل النموذج وعندما يتم توزيع الحمل على مساحة اوسع تقل احتمالية الفشل، وعند أستخدام الخزف بدلا من المينا زادت احتمالية فشل النموذج لنفس قيمة الحمل وبنفس منطقة تأثير الحمل ER -