@Article{, title={The Effect of Area Reduction of Forward Die on the Combined Forward- Backward Extrusion Process تأثير التخفيض في مساحة القطع للقوالب الأمامية (Forward) في عملية البثق المركب (Forward- Backward}, author={Ali Hassan Saleh علي حسين صالح and Muhsin Jabur Jweeg محسن جبر جويج and Jamal Hussien Muhamed جمال حسين محمد}, journal={Al-Nahrain Journal for Engineering Sciences مجلة النهرين للعلوم الهندسية}, volume={12}, number={2}, pages={108-121}, year={2009}, abstract={The effect of reduction area for flat and conical dies in forward-backward extrusion process was investigated experimentally using flat punches with three reduction areas (0.305,0.444,0.605), 0.444 with cone angles (60o,90o,120o) and polygonal punches (hexagonal and square).Three reduction areas of dies (0.395, 0.555, 0.691) are used. The results show that the extrusion load is effected with reduction area of flat dies more than conical dies when using cone and flat punches while the reduction area of conical dies affected with square punch more than hexagonal punch and this result was inversed with flat dies. The relative extrusion pressure P/Y ̅ increases when the reduction area of conical and flat dies increases too for all punches, but this result contrasts with the square punch at conical dies.The less value of max. stress was found with cone punch of prism angle 120o among cone punches for conical dies except the die of reduction area (0.555) and the cone punch of 90o prism angle gave less max. stress with all flat dies. Flat punch of reduction area (0.444) among the flat punches gave less value of max. stress with all conical dies and flat die of reduction area (0.691).

تم دراسة تاثير التخفيض في مساحة المقطع للقوالب المسطحة والمخروطية في عملية البثق المركب عمليا باستخدام مكابس مسطحة بنسب تخفيض في مساحة المقطع (0.305,0.444,0.605 (ومكابس مخروطية بثلاث زوايا (60o,90o,120o) ذات نسبة تخفيض ثابتة (0.444) ومكابس مضلعة الشكل (سداسي ، مربع) ذات نسبة تخفيض في مساحة المقطع متساوية (0.444 (.تم استخدام ثلاثة نسب تخفيض في مساحة المقطع للقوالب هى(0.395, 0.555, 0.691) .النتائج اظهرت ان حمل البثق يتأثر بنسبة تخفيض المساحة للقوالب المسطحة اكثر من القوالب المخروطية عند استعمال المكابس المخروطية والمسطحة بينما يتأثر حمل البثق بنسبة تخفيض القوالب المخروطية مع المكبس المربع الشكل اكثر من المكبس السداسي الشكل ، بينما تنعكس هذه النتيجة مع القوالب المسطحة . ان ضغط البثق النسبي (P/Y ̅) يزداد عندما تزداد نسبة التخفيض في مساحة المقطع للقوالب المخروطية الشكل والمسطحة مع كافة المكابس الا ان هذه النتيجة مختلفة في المكبس المربع مع القوالب المخروطية . ان ضغط البثق النسبي يتغير مع نسبة تخفيض المساحة للقوالب المسطحة مع المكابس المضلعة.} }