TY - JOUR ID - TI - STUDY THE CREEP OF TUBULAR SHAPED FIBER REINFORCED COMPOSITES AU - Dr. Najat j. Salah Dr. Adnan A. Abdul Razak , Hussein Ali Hamid AL-Abdly Hassen Sh. Majdi PY - 2008 VL - 15 IS - 4 SP - 27 EP - 44 JO - Tikrit Journal of Engineering Sciences مجلة تكريت للعلوم الهندسية SN - 1813162X 23127589 AB - In present work tubular –shaped fiber reinforced composites were manufactured by using two types of resins ( Epoxy and unsaturated polyester) and separately reinforced with glass, carbon and kevlar-49 fibers (filament and woven roving), hybrid reinforcement composites of these fibers were also prepared. The fibers were wet wound on a mandrel using a purposely designed winding machine, developed by modifying an ordinary lathe, in winding angle of 55 for filament. A creep test was made of either the full tube or specimens taken from it. Creep was found to increase upon reinforcement in accordance to the rule of mixture and mainly decided by the type of single or hybridized fibers. The creep behavior, showed that the observed strain tends to appear much faster at higher temperature as compared with that exhibited at room temperate. The creep rate also found to be depending on fiber type, matrix type, and the fiber /matrix bonding. The creep energy calculated from experimental observations was found to exhibit highest value for hybridized reinforcement.

في البحث الحالي تم تصنيع مواد متراكبة أنبوبيه باستخدام نوعين من الراتنجات وهي الايبوكسي و البولي استر غير المشبع وتم تسليح هذه الراتنجات بالألياف بصوره منفردة حيث استخدمت ألياف الزجاج, الكاربون و الكفلر49 (بشكل خيوط أو حصيره محاكه) كما تم استعمال هجين من هذه الألياف لاجل تسليح الراتنجات أيضا. تشمل عمليه تصنيع المتراكبات الانبوبيه بطريقه اللف الخيطي, تصميم و تصنيع قالب معدني للحصول على هذه الأشكال و بعدها تتم عمليه ترطيب الألياف أولا بأمرأرها خلال محلول الراتنج ثم لفها على قالب التشكيل باستخدام مخرطة حورت لهذا الغرض للحصول على الأشكال الانبوبيه المطلوبة و بزاوية لف 55 درجه للألياف .أظهرت اختبارت الزحف بان الانفعال في درجات الحراره العاليه اسرع بكثير عند مقارنته بتلك التي يظهرها بدرجه حراره الغرفه ، وهذا يحصل بصوره أساسيه بسبب ان جزيئات الماده البولميريه تكون اكثر حريه في الحركه في درجات الحراره العاليه واتي تودي الى سرعه حصول التشوهات في النماذج . ووجد كذلك ان معامل الزحف يعتمد على نوع الالياف ، نوع الراتنج وكذلك نوع التأصر بين الليف و الراتنج ، أعلى قيمه لطاقه الزحف المحسوبه من التجارب العمليه ظهرت عند أستخدام النماذج الهجينه . ER -