TY - JOUR ID - TI - CALCULATION OF A DORSIFLEXION ANGLE OF A PROSTHETIC FOOT FOR AMPUTEES BY USING DEVELOPED TACTILE DISPLACEMENT SENSOR AU - Muhsin J. Jweeg محسن جبر جويج PY - 2010 VL - Engineering Sc. Conference IS - First SP - 76 EP - 91 JO - DIYALA JOURNAL OF ENGINEERING SCIENCES مجلة ديالى للعلوم الهندسية SN - 19998716 26166909 AB - ABSTRACT:-This research aims to design, construct, and evaluate a tactile sensor for measuring displacements. The sensor is then employed in a developing computerized displacement measurement in order to assess its potential in sensing and evaluating a dorsiflexion angle of a new dynamic prosthetic foot for amputees. The developed system consists of three main parts namely, the sensor, the data acquisition unit that includes an analogue to digital (ADC) module, and a computer to aid in the processing of acquired data. One type of tactile sensors was used in the investigation. That is Potentiometric-based displacement sensors. That sensor provide analogue output signals, hence, to enable its input to the employed computer these signals are converted to digital type by the developed ADC-based module which is interfaced to the computer via the Enhanced Parallel Port (EPP). A number of tests were conducted to establish valid calibration of the system. Early experimental results showed that there are matching between the obtained results and the best fit lines when measuring linear displacement and using the traditional calibration method, therefore, the researcher decided to use that developed sensor in measuring the dorsiflexion angle of the new dynamic prosthetic foot and comparing the obtained results with the standard one.Key words: Prosthetic foot, Dorsiflexion angle, Tactile displacement sensor.

الخلاصة يهدف هذا البحث إلى تصميم وبناء وتقييم متحسس أزاحه تلامسي لقياس الإزاحات كما واستخدم المتحسس لقياس الجانبية في نظام حاسوبي مطور وذلك لتقييم إمكانياته في التحسس والتقييم لزاوية الانحناء الطولي للقدم الصناعية الديناميكية المستخدمة من قبل المعاقين. يتكون النظام المطور من ثلاثة أجزاء رئيسية وهي المتحسس ووحدة استحصال البيانات والتي بدورها تتكون ضمنا من محول اشاره تماثليه إلى رقمية ( Analogue to Digital Converter ADC ) والجزء الثالث هو الحاسوب والذي يساعد في معالجة البيانات المستحصله. تم في هذا البحث استخدام نوع واحد من المتحسسات التلامسية وهو متحسس أزاحه تلامسي باستخدام المجهاد( Potentiometric Tactile Displacement Sensor ) و يولد هذا المتحسس إشارات خارجه تماثليه ولكي يتمكن الحاسوب من معالجة تلك الإشارات لابد من تحويلها إلى إشارات رقميه وباستخدام محول الإشارات ( ADC ) والموصل للحاسوب من خلال القناة المتوازية .(Enhanced Parallel Port E.P.P.) أجريت العديد من التجارب العملية لمعايره نظام التحسس المطور. أظهرت النتائج العملية الاوليه وجود تطابق في القيم المستحصله من النظام عن المستقيم الأفضل عند قياس الإزاحات الخطية وباستخدام طريقة المعايرة التقليدية (Traditional Calibration ) وعليه قرر الباحث استخدام هذا المتحسس في قياس زاوية الانحناء الطولي للقدم الصناعية الديناميكية الجديدة ومقارنة النتائج المستحصله مع النتائج القياسية. ER -