TY - JOUR ID - TI - Effect of Addition Of Copper and Copper –Nickel Elements on Structure and Properties of Low Carbon Steels تأثير إضافة عنصر النحاس وعنصري النحاس والنيكل على التركيب والخواص للفولاذ المنخفض الكربون AU - Munthir Mohammed Radhy PY - 2010 VL - 28 IS - 23 SP - 6688 EP - 6702 JO - Engineering and Technology Journal مجلة الهندسة والتكنولوجيا SN - 16816900 24120758 AB - The purpose of this study is to investigate the effect of adding different amounts(2, 4, 6% of Cu) on properties and microstructure of low carbon steel .Also studythe effect of the same amounts of Cu with half amount of Ni(1,2,3%Ni) are addedon properties of low carbon steels. All these alloys(Fe-Cu,Fe-Cu-Ni) appear anincrease of hardness and strength with increase of the amount of Cu or Cu-Ni. Themicrostructure obtained after heat treated(quenched and aging) of Fe-Cu and Fe-Cu-Ni alloys has been studied by optical microscopy, investigated by X-raydiffraction and hardness measurement. The microstructures obtained afterquenching depending on composition and cooling rate, the massive ferrite andmassive martensite appears on most of structures in above alloys. Themicrostructure after aging of above alloys shown some of precipitates appear asdash plates, rod and spheres in ferrite or martensite structure and this precipitatesappear as X-ray diffraction were identified the copper rich phase €.

الغرض من هذه الدراسة هو بحث تأثير إضافة كميات مختلفة من عنصر النحاس بنسبة2,4,6% ) على الخواص الميكانيكية والتركيب المجهري للفولاذ المنخفض الكاربون كذلك )دراسة تأثير إضافة عنصر النحاس بنفس النسبة اعلاة مع نصف كمية النحاس من عنصرالنيكل(% 3,2,1 ) على الخواص الميكانيكية والتركيب المجهري للفولاذ المنخفض الكاربون.جميعالسبائك تظهر زيادة في الصلادة ومقاومة الشد مع زيادة كمية النحاس او كمية النحاس والنيكل.التركيب المجهري الناتج بعد عملية المعاملة الحرارية(االاخماد والتعتيق) لسبائك الحديد- نحاسX والحديد- نحاس-نيكل يدرس بواسطة المايكروسكوب الضوئي ويفحص بواسطة اشعة الحيودوتقاس صلادتة. التركيب المجهري التي يظهر بعد عملية االاخماد فقط يعتمد على كمية النحاسوالنيكل في السبيكة وعلى معدل التبريد, حيث يلاحظ ظهور فرايت كتلي اومارتنسايت كتلي فياغلب السبائك اعلاة . التركيب المجهري الناتج بعد عملية التعتيق يظهر رواسب بشكل الواحمتقطعة وقضبان وكرات في قوام فيراتي او مارتنسايتي وهذه الرواسب هي على الاغلب تؤشرظهور النحاس بشكل طور.(€) X في فحص أشعة الحيود ER -