TY - JOUR ID - TI - Evaluation Study of Glass Fiber Reinforced Polyester and Kevlar Reinforced Polyester by Taguchi Method دراسة تقييم ما بين البولي استر المقوى بالياف الزجاج والبولي استر المقوى بالياف الكفلر بواسطة طريقة تاكوجي AU - Osama Sultan M. أسامة سلطان محمد AU - Majid Hmeed A. ماجد حميد عبد المجيد AU - Ishraq Abdul Razaq K. اشراق عبد الرزاق كاظم PY - 2012 VL - 8 IS - 4 SP - 53 EP - 61 JO - Al-Khwarizmi Engineering Journal مجلة الخوارزمي الهندسية SN - 18181171 23120789 AB - In the present investigation two different types of fiber reinforced polymer composites were prepared by hand lay-up method using three different parameters (curing temperature, pressing load and fiber volume fraction). These composites were prepared from the polyester resin as the matrix material reinforced with glass fibers as first group of samples and mat Kevlar fibers as the second group, both with different volume fractions (4%, 8%, and 12%) of fibers. They were then tested by tensile strength and impact strength. The main objective in this study is to use Taguchi method for predicting the better parameters that give the better tensile and impact strength to the composites, and then preparing composites at these parameters and comparing them with the randomly used once. The experimental and analytical results showed that the Taguchi method was successful in optimizing the parameters that give the highest properties and it can find the most influential parameter regardless of the material used. Also it showed that the volume fraction was the most influential parameter on the tensile and impact strength. The difference between these composites was in the properties values and that the Kevlar composites have higher tensile and impact strength.

تم في هذا البحث تحضير مادتين متراكبتين مختلفتين من البوليمر المقوى بالالياف بواسطة طريقة التحضير اليدوي وباستخدام ثلاثة متغيرات هي (درجة حرارة المعالجة، حمل الكبس و الكسر الحجمي للالياف). تم تحضير المواد المتراكبة من راتنج البولي استر كمادة اساس مقوى بالياف الزجاج كمجموعة اولى من العينات والياف الكفلر كمجموعة ثانية من العينات وبكسور حجمية مختلفة لكل نوع من الالياف هي (4%، 8%، 12%). تم بعدها اجراء اختباري مقاومة الشد ومقاومة الصدمة على العينات. ان الهدف الاساسي من البحث هو استخدام طريقة تاكوجي للتكهن بافضل المتغيرات التي تعطي افضل مقاومة شد وصدمة للمواد المتراكبة ومن ثم تحضير مواد متراكبة عند هذه المتغيرات ومقارنتها مع المتغيرات المستخدمة المختارة عشوائيا. اظهرت النتائج التجريبية والتحليلية بان طريقة تاكوجي كانت ناجحة في التكهن وايجاد المتغيرات التي تعطي اعلى الخواص وكذلك يمكنها ايجاد المتغير الاكثر تاثيرا على الخواص بغض النظر عن المادة المستخدمة. اظهرت النتائج كذلك بان الكسر الحجمي كان المتغير الاكثر تاثيرا على مقاومة الشد والصدمة. كذلك ان الفرق بين المادتين المحضرتين كان في قيم الخواص وان المادة المتراكبة ذات الياف الكفلر اعطت مقاومة شد وصدمة اعلى. ER -