TY - JOUR ID - TI - Effect of using two packing Technic on Hardness of two dental acrylic resin AU - Najim O. Nasser PY - 2012 VL - 25 IS - 1 SP - 12 EP - 18 JO - Iraqi National Journal of Nursing Specialties المجلة العراقية الوطنية للاختصاصات التمريضية SN - 29585740 29585759 AB - Objective: the aim of this study is to invest age and determine the effect of using (2) packing technique (conventional and new tension technique) on hardness of (2) types of heat cure acrylic resin which are (Ivoclar and Qual dental type). Methodology : this study was intended the using of two types of heat cure acrylic (IVoclar and Qual dental type) which are used in construction of complete denture which packed in two different packing technique (conventional and new tension technique) and accomplished by using a total of (40) specimens in diameter of ( 2mm thickness, 2 cm length and 1 cm width) . This specimens were sectioned and subdivide into (4) group each (10) specimens for one group , then signed as (A, Al B , B 1) according to the method of technique and type of acrylic that used . The hardness of the specimens were measured by shore hardness test in technology university, Baghdad. Results: this study revealed that the type of acrylic which packed by new tension technic had less effect by hardness in compared with conventional packing technic, the result also showed that the type of acrylic resin have a little effect on hardness of the two types, and also it show highly mean value of hardness was indicate in Qual dental type in conventional technique, while the least mean value of hardness showed in Ivoclar type in new tension technique. Recommendations : this study has been conducted as a preliminary for future studies to give a sit of about the effect of hardness on other types of commercial heat acrylic resin that used in construction of prosthodontics restoration and dented prosthesis, it necessary to evaluate the hardness of any material used in construction of denture bases , it is suggested to under take a farther studies about using advance technique and better apparatus and device in packing the acrylic material and measured the value of hardness and its effect on this material.

الهدف : تهدف الدراسة الى بيان مدى تأثير طريقتي تعليب ( الطريقة العادية للتعليب ثم طريقة الضغط الجديد ) على نوعين من مادةة الاكريلك الحار المستخدم في صناعة طقوم الأسنان وهما ( الإيفوكلار والكويل دينتل) على صلادة هذين النوعين من المادة . المنهجية : أجريت الدراسة باستخدام نوعين من مادة الاكريلك الحار المستخدم في تصنيع الطقوم نوع (الإيفوكلار) ثم نوع ( الكوايل دينتل) ثم تعليب هذين النوعين بطريقتين مختلفتين ، بالطريقة العادية لتعليب المادة أولاً ثم باستخدام جهاز الضغط الجديد ثانياً . تمت الدراسة باستخدام (40) عينة ونموذج بابعاد (2 ملم سمك ، 2 سم طول ، 1 سم عرض ) للعينة ، وزعت إلى اربع مجاميع بواقع (10) عينات لكل مجموعة ، وزعت المجاميع الاربعة وفق التأشيرات حسب طريقة التعليب المستخدمة ونوع الأركيلك المستخدم والطريقة المستخدمة .تم قياس الصلادة بمقياس شور للصلادة الجامعة التكنولوجية – بغداد . النتائج : اظهرت نتائج الدراسة التي خضعت للتحليل الإحصائي ان مادة الاكريلك المعلبة بنظام الضغط الجديد قليل التأثير على صلادة المادة في الطريقة العادية وأن لا تأثير على نوع الاكريلك المستخدم في الطريقتين كذلك بينت الدراسة ان اعلى قيمة لمتوسط الصلادة ظهرت في الطريقة العادية بينما اقل معدل للصلادة في الطريقة الاخرى كذلك تبين من الدراسة ان اعلى قيمة لمتوسط الصلادة ظهر في نوع ( الكوايل دينتل) في الطريقة العادية في حين معدل الصلادة لنوع (الإيفوكلار) كان بنسبة أقل . التوصيات : هذه الدراسة اعدت لتكون تمهيداً لسلسلة من الدراسات المستقبلية لبيان مدى تأثير الصلادة على أنواع اخرى من مادة الاكريلك التجاري المستخدم في صناعة الاسنان وإيجاد طرق أخرى مستحدثة لتعليب المادة باستخدام تقنيات حديثة. ونقترح تجهيز مختبرات صناعة الاسنان بأجهزة حديثة واستخدام التقنيات العالية في جميع مراحل وخطوات اعمال مادة الاكريلك المستخدمة في صناعة طقوم الاسنان وطرق قياس وتأثير خاصية الصلادة على هذه المادة . ER -