@Article{, title={The Effect of Load Punch in the Limits of Strain paths for (1006) Steel Sheets by using Stretch Forming تأثير الحمل المسلط من قبل الخرامة على حدود مسارات الانفعال لصفائح من الصلب (1006)باستخدام التشكيل بالمط}, author={Anas Obeed Balod انس عبيد بالود}, journal={Anbar Journal of Engineering Sciences مجلة الأنبار للعلوم الهندسية}, volume={المؤتمر الهندسي الأول لكلية الهندسة}, number={العدد الخاص - الجزء الأول}, pages={102-113}, year={2012}, abstract={To control on the operation of sheet metal forming without failure, A diagram is used in which the range accepted, failure and critical deformation range are shown. This diagram is known as the Forming limit diagram. It is considered as one of the important tool to determine the formability of sheet metals. Every sheet metal has its own forming limit diagram which determines its formability, strain limit and the forming regions. In this paper, the forming limit diagrams (FLDs) were experimentally evaluated for low carbon steel sheets with different thickness (0.6, 0.75, 0.85, 1.2mm). The highest limit strain in the forming limit diagram is found in the steel sheet at thickness (1.2mm) and the lowest limits in the steel sheet at (0.6mm), this meaning that the formability improve with increase the thickness of steel sheet. The effect of load punch is higher at biaxial stretch path and the lowest at uniaxial tension path. The load punch is change with different thickness of sheet at the same path. The maximum thinning is found in the biaxial stretch path and the lowest of thinning in plane strain path for all sheets.

لكي نسيطر على عملية تشكيل الصفائح دون حدوث فشل يتم استخدام مخطط يُبَين فيه مناطق التشكيل المقبولة ومناطق الفشل والمناطق الحرجة وهو مخطط حد التشكيل. يعتبر مخطط حد التشكيل من الأدوات والوسائل المهمة في تحديد قابلية تشكيل الصفائح المعدنية. لكل صفيحة معدنية منحني حد تشكيل خاص بها يحدد قابليتها على التشكيل وحدود الانفعال ومناطق التشكيل. في هذا البحث تم تعيين منحني حد التشكيل عمليا لصفائح من الصلب مختلفة السمك (0.6, 0.75, 0.85, 1.2mm) ووجد إن أعظم قيمة لحدود الانفعال في منحني حد التشكيل عندما تكون صفيحة الصلب ذات سمك (1.2mm) واقل قيمة عندما تكون صفيحة الصلب ذات سمك (0.6mm) وهذا يدل على أن قابلية التشكيل تتحسن مع زيادة سمك الصفيحة. وأن تأثير الحمل المسلط من قبل الخرامة يكون أعظم عند مسار الشد ثنائي المحور وأقل عند مسار الشد أحادي المحور.كذلك فأن الحمل المسلط من قبل الخرامة يتغير مع اختلاف السمك عند نفس مسار الانفعال. أن أعظم ترقيق حدث عند مسار الشد ثنائي المحور وأقل ترقيق عند مسار الانفعال المستوي.} }