@Article{, title={Effect the Grain Size on the Polymer Matrix Composites Reinforced by Reenia Particles تأثير الحجم الحبيبي على مادة متراكبة ذات أساس بوليمري مقواة بدقائق من مادة (Reenia)}, author={Kdhim khaion kahlol كاظم خيون كحلول and Hayder Abbas Sallal حيدر عباس صلال and Mohammed A.sadik A.hassan محمد عبد الصادق عبد الحسن}, journal={Al-Khwarizmi Engineering Journal مجلة الخوارزمي الهندسية}, volume={9}, number={2}, pages={94-102}, year={2013}, abstract={Synthetic polymers such as polyurethane are used widely in the field of biomedical applications such as implants or part of implant systems.This paper focuses on the preparation of base polymer matrix composite materials by (Hand Lay-Up) method, and studying the effect of selected grain size (32, 53, 63, 75, and 90) µm of (Reenia) particles on some properties of the prepared composite.Mechanical tests were used to evaluate the prepared system (Tensile, Compression, Impact, and Hardness) tests, and a physical test of (Water absorption %), and all tests were accomplished at room temperature.Where results showed tensile test (maximum tensile strength and modulus of elasticity) high at small grain size while the percentage of elongation decreased with increasing size. As the compressive strength increased with small grain size. And also the values of hardness and fracture energy affected by particle size where the hardness and fracture energy increased at small particles size of compared to larger particles size. While the percentage of water absorption increased at large particle size.In general the results showed clear improvement in properties and maximum values which get it of tensile strength, Modulus of elasticity, elongation percentage, compression strength, fracture energy, hardness and water absorption were as follows ((34.8 MPa), (10%), (268 N/mm2), ( 54.2 MPa),( o.408 J), (78.9 Shor (D)), (0.2668 %)) at using (32µm)) except water absorption was at (90µm) .

يركز هذا البحث على تحضير مادة متراكبة ذات اساس بوليمري بطريقة (الصب اليدوي)، ودراسة تأثير الحجوم الحبيبة المختارة (32 , 53 , 63 , 75 ,90) مايكرون من مادة (Reenia) (وبكسر وزني ثابت 12% ) على خواص المادة المتراكبة المحضرة، حيث أن مادة الاساس المستخدمة هي راتنج البولي يوريثان (PU).عدد الاختبارات الميكانيكية التي أجريت لتقييم النظام المتراكب المحضر تتضمن (الشدّ، الانضغاط، الصدمة والصلادة)، بالإضافة الى الاختبار الفيزيائي (النسبة المئوية لامتصاصية الماء)، وكل الاختبارات اجريت في درجة حرارة الغرفة.حيث اظهرت نتائج اختبار الشد (اقصى مقاومة شد ومعامل المرونة ) ارتفاع عند الحجوم الدقائقية الصغيرة بينما قلت النسبة المئوية للأستطالة مع زيادة الحجم الدقائقي .كما ان مقاومة الانضغاط ازدادت مع الحجوم الدقائقية الصغيرة .وأيضا قيم الصلادة و طاقة الكسر تأثرت بالحجم الدقائقي حيث ارتفعت الصلادة وطاقة الكسر عند الحجوم الصغيرة للدقائق مقارنة بالحجوم الأكبر. بينما النسبة المئوية لامتصاص الماء ازدادت مع ارتفاع الحجوم الدقائقية .بشكل عام أظهرت النتائج تحسن واضح بالخواص وكانت القيم القصوى التي تم الحصول عليها لمقاومة الشد والنسبة المئوية للأستطالة ومعامل يونك ومقاومة الانضغاط وطاقة الكسر والنسبة المئوية لامتصاص الماء كانت مرتبة كالتالي ((34.8(MPa (10%) ,(268 نت/ملم2), (54.2(MPa ، (0.408 J) ،( Shor (D) 78.9)، (0.2668%) عند الحجوم ( 32) مايكرون ماعدى الامتصاصية كانت عند الحجم (90) مايكرون.} }