@Article{, title={Comparison study of some mechanical properties of micro and nano silica EP composites دراسة مقارنة بين بعض الخصائص الميكانيكية للمتراكبات النانوية والمايكرو المكونة من الايبوكسي وحبيبات السيليكا}, author={Ekram A. Al-Ajaj اكرام عطا العجاج and Harith I. Jaffer حارث ابراهيم جعفر and Muhannad M. Abd مهند مهدي عبد}, journal={Iraqi Journal of Physics المجلة العراقية للفيزياء}, volume={10}, number={18}, pages={62-68}, year={2012}, abstract={The effect of micro-and nano silica particles (silica SiO2 (100 μm), Fused silica (12nm)) on some mechanical properties of epoxy resin was investigated (Young's modulus, Flexural strength). The micro-and nano composites were prepared by using three steps process with different volume fraction of micro-and nano particles (1, 2, 3, 4, 5, 7, 10, 15, and 20 vol. %). Flexural strength and Young's modulus of nano composites were increased at low volume fraction (max. enhancement at 4 vol.% ). However at higher volume fraction both Young's modulus and flexural strength decrease. Moreover, above, the mechanical properties are enhanced more than that of neat epoxy resin. The flexural strength decreases with increasing the volume fraction of micro silica especially at high volume fraction while Young's modulus increases with increasing the volume fraction. Gelling time of epoxy resin was highly affected by adding nano-particles and also using ultrasonic homogenizer. It was found that mode failures were depend on particles size and volume fraction.

تمت دراسة تاثير المضافات النانوية لجسيم السيليكا ( SiO2- 12 nm ) والمضافات المايكروية لجسيم السيليكا (SiO2-100 µm) على الخصائص الميكانيكية ( قوة الانحناء، معامل المرونة) لمادة الايبوكسي. حضرت المتراكبات النانوية والمتركبات المايكروية باستخدام طريقة من ثلاث مراحل (الخلط الميكانيكي والخلط بالامواج فوق الصوتية واستخدام تقنية التفريغ) ولعدة نسب حجمية (1, 2, 3, 4, 5, 7, 10, 15, 20%) حيث وجد ان قوة المتانة ومعامل المرونة يزداد بزيادة نسب الاضافات للمتراكبات النانوية وخصوصا في النسب ذات الاضافات القليلة حيث وصلت اعلى نسبة تحسن في الاضافة 4% وفي نسب الاضافات الاعلى ينخفض التحسن مع بقاء الخصائص الميكانيكية للمتراكبات اعلى من الخاصائص الميكانيكية لمادة الايبوكسي في حين ان اضافة الجسيمات المايكروية تؤدي الى انخفاض المواصفات الميكانيكية للمتراكبات مع ارتفاع معامل المرونة للمتراكبة المايكروية.كما قد لوحظ ان زمن التصلب يتأثر بأضافة المواد النانوية وبأستخدام طريقة خلاط الاهتزازات فوق الصوتية. ووجد ان نوع الفشل في العينة يتمدد على حجم وتركيز المضافات.} }