TY - JOUR ID - TI - INFLUENCE OF DIFFERENT FACTORS ON ADHESIVE LINE SOLIDIFICATION IN SHEAR TENSION TEST AND DRY AND WET TENSILE TENSION TEST OF WOOD STRUCTURE تاثير عوامل مختلفة لتصلب الخط الصمغي في قوة الشد للقطع المائل وقوة الشد الجاف والرطب في التراكيب الخشبية AU - Abdul-Razzak R. S. Al –Malah عبدالرزاق رؤوف سليمان الملاح AU - Alaa O. A. Al – Hamedi آلاء عمر احمد PY - 2013 VL - 41 IS - 2 SP - 167 EP - 180 JO - Mesopotamia Journal of Agriculture مجلة زراعة الرافدين العراقية SN - 1815316X AB - This study was conducted to test the strength of glue line in wood structures by using some mechanical tests (shear strength test, Dry and wet tensile tests). Two kinds of adhesives (Urea-formaldehyde (UF) and poly-vinyl acetate (PVA) with three types of wood surfaces (Pure Pine, Pure Sycamore and substrate of Pine with Sycamore) and two methods of adhesive curing (Electrical and microwave domestic ovens) were used. It was shown from the study results that wood type had an effect in share tension test, pine wood gave the best results followed by shear tension of sycamore wood and pine with sycamore wood, but there were no significances between the three types of woods. Urea formaldehyde adhesive got the highest shear tension values when compared with PVA adhesive. Solidification by using electrical oven method gave the best values in shear tension as compared with the microwave oven curing method. The results also showed that 1 gm adhesive quantity gave the best results as compared with 0.75 gm and 0.5 gm in shear tension. Concerning the dry and wet tensile tension of the PVA glue line by using electrical oven dry, microwave oven and room temperature solidification methods, the results showed that pine wood had greater dry and wet tensile tension than sycamore wood and pine with sycamore wood. Also, parallel grain direction gave the best values as compared to perpendicular grain direction for both dry and wet tensile tension. The results also showed that the highest dry tensile tension was by using electrical oven solidification method، followed by room temperature method، while solidification by using microwave oven gave the lower tensile tension value. Room temperature solidification method gave the best results in tensile tension after emersion in water for 30 and 60 minute as compared to electrical oven and microwave oven solidification process respectively. Also, 2 gm adhesive gave the best results in tensile tension compared to 1.5 gm and 1 gm adhesive quantities.

أجريت هذه الدراسة لبيان مدى قوة ومتانة الرابطة اللصقية وذلك بإجراء الاختبارات الميكانيكية على الخط الصمغي وهي قوة الشد للقطع المائل و قوة الشد الجافة والرطبة وباستخدام نوعين من اللواصق: اليوريا – فورمالدهايد Urea-Formaldehyde (UF) والغراء Polyvinyl acetate (PVA) وباستخدام ثلاثة أنواع من الأخشاب كأسطح للصق وهي: خشب الصنوبر Pinus brutia Ten. وخشب الجنار الغربي Platanns occidentalis L. وخشب الجنار مع خشب الصنوبر، فضلاً عن استخدام طريقتين لتصلب الخط الصمغي: الفرن الكهربائي وفرن الموجات الدقيقة. تبين من نتائج الدراسة أن نوع الخشب كان له تأثير في قوة الشد للقطع المائل، وقد أعطى خشب الصنوبر أفضل النتائج يليها قوة الشد في خشب الجنار ثم خشب الجنار مع خشب الصنوبر ولكن لم يكن هناك فروقات معنوية بين انواع الخشب المستخدمة، وقد حصل لاصق اليوريا – فورمالدهايد على قوة شد أعلى من لاصق الغراء، وأن طريقة التصلب بالفرن الكهربائي كانت الأفضل في قوة الشد للقطع المائل مقارنة مع طريقة التصلب بفرن الموجات الدقيقة. كما أظهرت النتائج أن كمية اللاصق 1 غم تفوقت على كمية اللاصق 0.75 غم و 0.5 غم في قوة الشد للقطع المائل. أما فيما يخص قوة الشد الجاف والرطب للخط الصمغي باستخدام طريقة التصلب بالفرن الكهربائي وفرن الموجات الدقيقة ودرجة حرارة الغرفة وباستخدام لاصق الغراء فقد أظهرت الدراسة بأن خشب الصنوبر له قوة شد جافة ورطبة أعلى من خشب الجنار وخشب الصنوبر مع خشب الجنار، كما إن اتجاه الألياف المتوازي أعطى نتائج أفضل من اتجاه الألياف المتعامد في صفة قوة الشد الجافة والرطبة. كما أوضحت النتائج أن أعلى قوة شد جافة كانت باستخدام الفرن الكهربائي وتليها طريقة التصلب بدرجة حرارة الغرفة، أما طريقة التصلب بفرن الموجات الدقيقة فقد كانت قوة الشد فيها أقل. أما قوة الشد الرطبة (بعد الغمر بالماء نصف ساعة وساعة) فقد أعطت طريقة التصلب بدرجة حرارة الغرفة قوة شد أعلى من طريقة التصلب بالفرن الكهربائي وفرن الموجات الدقيقة على التوالي. كما أظهرت النتائج أيضا تفوق قوة الشد الجافة والرطبة لكمية ألاصق 2غم على كمية اللاصق 1.5 و 1 غم. ER -