TY - JOUR ID - TI - Catalysts Regeneration Using Laser Technique in Petroleum Industry تنشيط العوامل المساعدة باستخدام تقنية الليزر في الصناعة النفطية AU - Adawiya J. Haider AU - Khalid A. Sukkar AU - Duha S. Ahmed PY - 2013 VL - 31 IS - 4 Part (A) Engineering SP - 715 EP - 722 JO - Engineering and Technology Journal مجلة الهندسة والتكنولوجيا SN - 16816900 24120758 AB - The catalyst cost regards one of the most important obstacles in petroleum industry. Therefore, the regeneration of catalysts could be more economic process to get high performance and low cost. In this work, three types of catalysts were investigated: Pt/A2lO3 (spent catalyst from reforming unit/Al-Doura Refinery), prepared Pt/A2lO3(Doura) and Pt/HY. The performances of catalysts (activity, selectivity and catalyst stablity) were studied using n-heptane as feedstock under reforming conditions. The operating pressure kept constant at atmospheric pressure, and the operating temperature 500 oC. The liquid flow was 0.4 l/h. The amount of catalyst was 50 gm, H2/H.C ratio used was 2 for all experimental runs.The catalyst of reforming process has been successfully regenerated using laser technique. This technique regards as a new approach for catalyst regeneration in petroleum industry to remove carbon deposits. On the other hand, this regeneration technique shows a great potential for economical processes in petroleum refineries. The results show that the best operating conditions for the regeneration process were: laser power of 13 watt and regeneration temperature of 650 oC. From the results of catalyst characterization it was concluded that the structures and morphology of all catalysts types did not effected or destroyed through using laser power.

تعتبر كلف شراء العوامل المساعدة من اهم الصعوبات التي تواجهها الصناعة النفطية، لذلك فان عملية تنشيط العوامل المساعدة واعادة استخدامها تكون طريقة عملية لتحسين الاداء والجانب الاقتصادي. في هذا البحث تم دراسة ثلاثة انواع من العوامل المساعدة التي تستخدم في وحدات التهذيب : مستهلك من مصفى الدورة Pt/A2lO3 و Pt/HY و Pt/A2lO3(Doura) كعوامل مساعدة محضرة. حيث تم دراسة فعالية وانتقائية ومدى فقدان الفعالية لهذه العوامل المساعدة من خلال استخدام الهبتان الاعتيادي كمادة اولية لتفاعلات التهذيب.أجريت التجارب تحت ضغط جوي اعتيادي ودرجة حرارة oC500 ومعدل جريان 4 لتر/ساعة للهبتان و 50 غم من وزن العوامل المساعدة ونسبة (HC/H2) تساوي 2 لجميع التجارب. اظهرت النتائج نجاح استخدام تقنية الليزر في تنشيط العوامل المساعدة المستخدمة في وحدات التهذيب، وتعتبر هذه الطريقة اسلوباً متطوراً لازالة الترسبات الكاربونية من سطح العمل المساعد في االصناعة النفطية. كما تعتبر هذه التقنية مجدية اقتصادياً في المصافي النفطية. اظهرت النتائج ان افضل ظروف التنشيط هي قدرة الليزر 13 واط تحت حرارة oC 650 . من خلال دراسة مواصفات العوامل المساعدة تم الاستنتاج بعدم تأثر التركيب الداخلي والتركيب السطحي لجميع العوامل المساعدة المستخدمة في التجارب خلال تعرضها لاشعة الليزر. ER -