TY - JOUR ID - TI - Effect of Aluminium Content on Some Physical and Mechanical Properties of The compounds With Base of Ceramic تأثير تغير محتوى الألمنيوم على بعض الخواص الفيزياوية والميكانيكية لمتراكبات ذات اساس سيراميكي AU - Abdul Majeed E. Ibrahim عبد المجيد عيادة ابراهيم AU - Raed N. Razooqi رائد نجيب رزوقي AU - Saif Amer Mahdi سيف عامر مهدي PY - 2013 VL - 18 IS - 4 SP - 205 EP - 216 JO - Tikrit Journal of Pure Science مجلة تكريت للعلوم الصرفة SN - 18131662 24151726 AB - This research includes the study of the effect of the Aluminium (Al) addition as reinforcement material at a different weight percentages (4,8,12,16,20) % to ceramic matrix material formed from ( Silicon Dioxide , Oxide Chromium (III) , Titanium Dioxide ) with fixed ratios of elements (Co , Ni) for each of them , by using powder metallurgy technique with pressure of (5) tons were used for forming. We have studied the effect of the Aluminium addition on some physical and mechanical properties of prepared sample after sintered it at (1000 Cº) for (2hr) .The results shown that the Aluminium addition have been enhanced the physical and mechanical properties of the Composites samples , When increasing the proportion of aluminum from (% 4) to (% 20) we note that Apparent density , specific gravity and hardness of the composite (C): [ Cr2O3 + Al + Co + Ni ] for example, had improved by (% 3.2) , (% 4.8) and (% 13) respectively, as for Composites (B): [ TiO2+ Al+ Co+ Ni ] and (A): [SiO2 + Al + Co + Ni ] are similar behavior with composite (C) but at low rates according to form of the composite .It is also found that relation between the Aluminium addition with the porosity and water absorption for all compound is an inverse relation , while their relations with the apparent density , specific gravity and other mechanical is a direct relation exact . And the Composite (C) which is containing (Cr2O3) showed the best properties with for all additional rates as a comparing with the other Composites.

يتضمن هذا البحث دراسة تأثير إضافة الألمنيوم ( Al ) كمادة تدعيم وبنسب وزنية مختلفة (4,8,12,16,20)% الى مواد ذات أساس سيراميكي متكونة من ( ثاني اوكسيد السليكون , ثاني اوكسيد التيتانيوم , اوكسيد الكروم الثلاثي ) مع نسبة ثابتة من عنصري ( Ni ,Co ) لكل منهم. باستخدام تقانة ميتالورجيا المساحيق وبضغط كبس (5 ton) لغرض التشكيل .تم دراسة تأثير نسب الإضافة على الخواص الفيزياوية والميكانيكية بعد تلبيدها بدرجة حرارة (1000°C) لمدة ( 2 hr) . وقد تم التوصل إلى أن زيادة نسبة الألمنيوم تعمل على تحسين الخواص الفيزيائية والميكانيكية للنماذج فعند زيادة نسبة الألمنيوم من (%4) إلى (%20) نلاحظ إن الكثافة الظاهرية والوزن النوعي والصلادة للمتراكب (C):[ Cr2O3+Al+Co+Ni]على سبيل المثال قد تحسنت بالنسب (%3.2) و (%4.8) و (%13) على التوالي أما المتراكبان (B):[TiO2+Al+Co+Ni] و SiO2+Al+Co+Ni] [:(A) فيتشابهان بالسلوك مع المتراكب C ولكن بنسب خواص أقل تبعاً لنوع المتراكب . وان علاقة نسبة إضافة الألمنيوم بالمسامية الظاهرية وقابلية امتصاص الماء للمتراكبات كافة هي علاقة عكسية , بينما تكون علاقتها طردية بالكثافة الظاهرية والوزن النوعي والخواص الميكانيكية الأخرى وان المتراكب (C)الذي يحتوي على اوكسيد الكروم الثلاثي (Cr2O3) أظهر أفضل الخواص ولجميع نسب الألمنيوم مقارنة بالمتراكبات الأخرى . ER -