TY - JOUR ID - TI - Evaluation the Effects of CO2 Laser on Soft and Hard Tissues (in vitro study) تقييم تأثير ليزر ثاني أوكسيد الكاربون على الانسجة الرخوة و الصلبة (دراسة خارج الجسم الحي) AU - Balkaiss A. Abdul Jaleel AU - Ali S. Mahmood PY - 2014 VL - 13 IS - B SP - 13 EP - 22 JO - Iraqi Journal of Laser المجلة العراقية لليزر SN - 18121195 26180596 AB - Abstract: CO2 laser (10.6 µm) is the most often used laser in the oral surgery due to its high absorption by water of the oral tissues. Several benefits of the use of CO2 laser have been reported for oral surgical procedures. This study aims to evaluate the effect of CO2 laser on soft and hard oral tissues (in vitro study). This study was done on fresh tissues from sheep’s head. CO2Surgical Laser with different operation modes was used; 0.2 mm spot size using different laser parameters on the tongue, and bone making holes, incisions and cutting. The depths and widths of holes and incisions were measured using endodontic file under magnification. The speed of incisions was calculated and the required time for cutting was measured using sport clock. The depths of holes and incisions were increasing with increasing the power density and pulse duration from 90 µs to 1.7 ms in 100 µs increments and so in CW mode (for holes 2.5 mm at 15W, for incisions 6mm at 20W). Also the diameter of holes was increasing with power (1.2 mm at 15W) .The required time for cutting was decreasing as the power increased (14.14 sec. at 25W). The use of CO2 laser can be considered practical, effective and easy to carry out holes, incisions, and cuttings.

الخلاصة: ليزر ثاني أوكسيد الكاربون (10.6مايكرومتر) هوالاكثر استخداما" في جراحة الفم ,وذلك لامتصاص ماء أنسجة الفم العالي له.لاستخدام ليزر ثاني أوكسيد الكاربون فوائد عديدة قد تم اقرارها في عمليات جراحة الفم. هو تقييم تأثير ليزر ثاني أوكسيد الكاربون على انسجة الفم الرخوة والصلبة (دراسة خارج الجسم الحي). في هذه الدراسة أستخدمت أنسجة طازجة مأخوذة من رأس خروف و ليزر ثاني أوكسيد الكاربون الجراحي ذو صيغ تطبيقية مختلفة , بنصف قطرحزمة (0.2مليمتر) بمعايير جرع ليزر مختلفة,على اللسان و العظم .لعمل ثقوب و شقوق وتقطيع. تم قياس عمق و عرض الثقوب و الشقوق باستخدام فايل حشوة الجذر(آلة قياس) تحت التكبير.وتم حساب سرعة عمل الشقوق وقياس الوقت اللازم لاكمال التقطيع بأستخدام ساعة رياضية. كانت أعماق الثقوب و الشقوق تزداد بأزدياد كثافة القدرة و عرض النبضة في الطراز النبضي (من 90مايكروثانية الى 1.7ملي ثانية بخطوات100مايكروثانية) وكذلك في طراز الموجة المستمرة (للثقوب 2.5مليمتر عند15 واط,وللشقوق 5مليمتر عند 20واط),وكذلك قطر الثقوب كان يزداد بأزدياد كثافة القدرة (1.2مليمتر عند 15 واط),أما الوقت اللازم لاكمال القطع كان يقل بأزدياد القدرة(14.14 ثانية عند 15 واط). أن أستخدام ليزر ثاني أوكسيد الكاربون من الممكن أعتباره عمليا" و فعالا" و سهلا" في أجراء الثقوب و الشقوق و التقطيع. ER -