TY - JOUR ID - TI - Effect of adding Potassium Alum powder on the Mechanical Properties and Flame-resistant of Low Density of Polyethylene (LDPE) تأثير إضافة مسحوق شب البوتاسيوم على الخواص الميكانيكيه ومقاومة اللهوبية للبولي اثيلين واطئ الكثافة (LDPE) AU - Ahmed J. Mohammed أحمد جاسم محمد AU - Ibrahim K. Ibrahim إبراهيم كاظم إبراهيم AU - Fayez J. Mohammed فائز جمعة محمد PY - 2014 VL - 5 IS - 1 SP - 46 EP - 51 JO - University of Thi-Qar Journal of Science مجلة علوم ذي قار SN - 19918690 27090256 AB - The Study of the Effect of Potassium Alum on the Mechanical properties of low density polyethylene (LDPE), which is manufactured in the General state company of petrochemical industries, Basra, as function of the percentages of Potassium Alum (2.5%, 5%, 10%, 15%, 20%), at particular size (150 µm) were investigated through several variables, such as, Young's modules, strength, and elongation. The obtained results were appeared that the added Alum to reduce the spaces between the polymer chains, which reflects the high ability of the polymer against the applied stress, and this increase will give further property that increase the hardness of the prepared specimens, the results lead to that the strength at both break will be affected little till the percentage (5%), and lowered after that with increasing the percentage also indicate an lowered in young's modules at the percentage (10%). The results also appear that the highest point of the stress is (10.95 N/mm2 ).The proportional limit was (163.6 N) for (10%), observe that the average time of burning starts strong impact when (5%) as increasing to(162 Sec) and then begins to decline behavior when increasing proportions weighted exception to this behavior when (20%).

تم إضافة مسحوق شب البوتاسيوم كحشوات مالئة وبنسب وزنيه (2.5%,5%,10%,15%,20%) وعند حجم دقيقه أما اقل أو مساو إلى (150 m) لبوليمر الاثيلين واطئ الكثافة LDPE والمصنع في معمل بتروكيمياويات البصره إذ تمت دراسة عدة متغيرات مثل الاستطالة وقوه الشد عند الوهن والقطع ومعامل يونك وبينت النتائج المستحصله ان الشب المضاف يعمل على تقليل الفراغات بين السلاسل البوليمريه مما يعكس إمكانية البوليمر العالية بتحمل الإجهاد المسلط عليه وتكون درجة التجانس عالية بين كل من البوليمر والحشوات، وان زيادة نسبة المالئات تضفي زيادة صفة الصلابة على النماذج المحضرة عند النسبة المئوية (%5)،ودللت النتائج إن سلوك قوة الشد عند القطع يكون ذا تأثير عند النسبة (% 5) من المضاف بعدها تهبط بزيادة كمية المضاف إذ تكون لمسحوق الشب كمواد مالئة تأثير على خصائص البولي اثيلين والذي له خصائص ميكانيكية ضعيفة لذلك تنخفض قوة الشد عند القطع ويلاحظ ايضا انخفاض معامل يونك مع نسبه المضاف (%10) مما يعكس مرونة البوليمر المطعم بشب البوتاسيوم وتوسع مدى التطبيقات لهذا البوليمر وبينت النتائج ان أعلى نقطه للإجهاد هي) .95 N/mm210)،وكانت أعلى قيمة لحد التناسب (proportional limit) 163.6 N للنسبة الوزنية % 10، ونلاحظ بان معدل زمن الاحتراق يبدأ بتأثير قوي عند النسبة (%5) إذ تصل قيمته إلى (162 Sec) وبعدها يبدأ السلوك بالانخفاض عند زيادة النسب الوزنية ويشذ هذا السلوك هند النسبة الوزنية (% 20). ER -