TY - JOUR ID - TI - Determination of Optimum Welding Parameters for FSW AA2024-T351 تحديد معاملات اللحام المثالية لسبائك الالمنيوم (AA2024-T351) الملحومة بواسطة لحام الخلط الاحتكاكي AU - Zuhair Altaher زهير الطاهر AU - Qasim Abbas Atiah قاسم عباس عطية AU - Samir Ali Amin Al-Rubaie سمير علي أمين الربيعي PY - 2015 VL - 11 IS - 1 SP - 51 EP - 64 JO - Al-Khwarizmi Engineering Journal مجلة الخوارزمي الهندسية SN - 18181171 23120789 AB - Friction stir welding is a relatively new joining process, which involves the joining of metals without fusion or filler materials. In this study, the effect of welding parameters on the mechanical properties of aluminum alloys AA2024-T351 joints produced by FSW was investigated.Different ranges of welding parameters, as input factors, such as welding speed (6 - 34 mm/min) and rotational speed (725 - 1235 rpm) were used to obtain their influences on the main responses, in terms of elongation, tensile strength, and maximum bending force. Experimental measurements of main responses were taken and analyzed using DESIGN EXPERT 8 experimental design software which was used to develop the response surface methodology (RSM) models. Mathematical model of responses, as functions of used welding conditions, were obtained and analyzed by ANOVA variance to verify the adequacy of these models. The resultant quadratic models showed that as the rotation speed or welding speed increases, the tensile strength and elongation of the joint firstly increase to a maximum value and then decrease more likely due to the occurrence of void defect. Increasing both welding speed and rotational speed leads to increase the maximum bending force firstly to a maximum value and then decreases. However, the welding speed was found more significant than rotational speed. A good agreement was found between the results of these models and optimization with the experimental ones with confidence level of 95%.

اللحام بالخلط الاحتكاكي هو عملية لحام جديدة نسبياً، و الذي يستلزم لحام المعادن بدون استخدام الانصهار او المواد المالئة. في هذه الدراسة، تم التحقق من تاثير معاملات اللحام على الخواص الميكانيكية لسبائك الالمنيوم (AA2024-T351) الملحومة بطريقة لحام الخلط الاحتكاكي.تم استخدام مديات مختلفة لمعاملات اللحام، بوصفها عوامل إدخال، مثل سرعة اللحام (6-34 mm/min) و السرعة الدورانية (725-1235 rpm) للحصول على تاثيرها على الاستجابات الرئيسة، بدلالة الاستطالة و مقاومة الشد، و قوة الانحناء العظمى. كما قد تم إستخدام و تحليل قياسات تجريبية للاستطالة، مقاومة الشد، وقوة الانحناء العظمى بإستعمال برنامج التصميم التجريبي (DESIGN EXPERT 8) للحصول على نماذج منهجية للاستجابة السطحية (RSM). كما تم إستحصال و تحليل النموذج الرياضي للإستجابات (الاستطالة، مقاومةالشد، وقوةالانحناءالعظمى) كدوال لضروف اللحام المستعملة باستعمال تباين ANOVA للتحقق من ملائمة هذه النماذج. النماذج المربعة الناتجة بينت بانه بزيادة سرعة اللحام و السرعة الدورانية، فانه تزداد مقاومة الشد و الاستطالة الى قيمة عظمى في البداية ثم تتناقص بسبب حدوث العيوب الفراغية. كما ان زيادة كلا من سرعة اللحام والسرعة الدورانية تؤدي الى زيادة قوة الانحناء العظمى اولاً الى قيمة عظمى ثم تتناقص. ومهما يكن من امر، فقد وجد بان سرعة اللحام تكون اكثر تاثيرا من السرعة الدورانية. و وجد توافق جيد بين نتائج هذه النماذج و الامثلية مع النتائج العملية بمستوى ثقة (95%). ER -